C1256 Accumulator Low Pressure
Diagnostic trouble codes · Vehicles built from Aug 2012
Versions by build date: Nov 2010 – Jul 2012 from Aug 2012
DESCRIPTION
The accumulator pressure sensor is connected to the skid control ECU in the master cylinder solenoid.

| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1256 |
Fluid pressure inside the accumulator drops below the specification value. |
|
INSPECTION PROCEDURE
- NOTICE:
- When replacing the master cylinder solenoid, perform zero point calibration (Click here).
- HINT:
- When DTC C1251, C1253 or C1254 is output together with DTC C1256 inspect and repair the trouble area indicated by DTC C1251, C1253 or C1254 first.
| 1. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Depress the brake pedal 20 times or more.
Turn the ignition switch to ON.
Wait for 99 seconds.
Check if the same DTC is recorded (Click here).
Result Result
Proceed to
DTC is output
A
DTC is not output
B
- HINT:
- Excessive brake pedal operation results in abnormal accumulator pressure consumption. This is normal.
|
|
||||
| A | |
| 2. INSPECT HYDRAULIC BRAKE BOOSTER ASSEMBLY FUNCTION |
Inspect brake booster pump power supply system function.
Turn the ignition switch off.
Depress the brake pedal 20 times or more to release the pressure in the accumulator.
- HINT:
- When the pressure is released, the brake pedal stroke becomes longer.
Check that the brake fluid level is at the MAX level.
Chock the 4 wheels and release the parking brake.
Turn the ignition switch to ON and measure the brake booster pump operating time (the time from when the brake booster pump starts operating until it stops).
- OK:
- 20 to 80 seconds
Start the engine after the brake boost pump stops.
Check that the ABS warning light and slip indicator light are not illuminated.
Turn off the engine, and then turn the ignition switch to ON.
Check that the brake boost pump operates and then stops when the brake pedal is depressed 4 or 5 times.
Depress the brake pedal 4 or 5 times and measure the brake booster pump operating time (the time from when the brake booster pump starts operating until it stops).
- OK:
- 2 to 11 seconds
Check that the brake warning light illuminates and the buzzer sounds when the brake pedal is fully depressed continuously 15 to 20 times.
- NOTICE:
- Wait 120 seconds or more after turning the ignition switch to ON before performing this inspection.
Check brake booster operation.
Turn the ignition switch off.
Depress the brake pedal 20 times or more to release the pressure in the accumulator.
- HINT:
- When the pressure is released, the brake pedal stroke becomes longer.
Depress the brake pedal, start the engine, and check the change in the brake pedal height.
- OK:
- The brake pedal moves slightly inward.
Inspect brake master cylinder fluid pressure change (Click here).
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (MASTER CYLINDER PRESSURE SENSOR) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item / Range
Normal Condition
Diagnostic Note
Accumulator Sensor
Accumulator pressure sensor reading / min.: 0 V, max.: 5 V
3.58 to 5 V
If value constant regardless of pump operation, accumulator pressure sensor malfunction suspected.
Check that the accumulator's output value is in the Normal Condition range.
- OK:
- Accumulator pressure sensor value is in the Normal Condition.
|
|
||||
| OK | |
| 4. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | ||
| ||
| 5. INSPECT BRAKE BOOSTER PUMP ASSEMBLY |
Remove the hydraulic brake booster assembly (Click here).
Using a screwdriver, remove the 2 screws and pull out the wire harness from the master cylinder solenoid.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
Red wire terminal - Black wire terminal
Always
Below 2 Ω
Text in Illustration *1
Pump motor wire harness
*a
Red wire
*b
Black wire
Install the pump motor wire harness to the master cylinder solenoid with the 2 screws.
- Torque:
- 2.9 N*m{ 30 kgf*cm , 26 in.*lbf }
|
|
||||
| OK | ||
| ||
