2011-2016 FJ Cruiser · Service Manual BRAKE

Brake Warning Light Remains ON

Circuit diagnosis · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 from Aug 2011

DESCRIPTION

The BRAKE warning light lights up when the brake fluid is insufficient, the parking brake is applied or the EBD is defective.

WIRING DIAGRAM

C164948E01

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. CHECK DTC
  1. Check for the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


2. CHECK BRAKE FLUID LEVEL
  1. Check the amount of brake fluid in the brake reservoir.

    OK:
    Brake fluid level is correct.



NG
ADD BRAKE FLUID
OK


3. CHECK SKID CONTROL ECU CONNECTOR
  1. Check whether the skid control ECU connector is connected securely.

    OK:
    The skid control ECU connector is connected securely.



NG
CONNECT CONNECTOR CORRECTLY
OK


4. INSPECT BRAKE FLUID LEVEL WARNING SWITCH

  1. F052341E05
    Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float UP
    1.9 k to 2.1 kΩ
    1 - 2
    Float DOWN
    Below 1 Ω

HINT:
If the result is as specified, adjust the brake fluid level to the MAX level after measuring the resistance.



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)

  1. F051748E03
    Disconnect the skid control ECU connector.

  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    A4-41 (LBL) - A14-2
    Below 1 Ω
    A4-41 (LBL)- Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT PARKING BRAKE SWITCH ASSEMBLY

  1. C129357E04
    Disconnect the parking brake switch connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Released
    Below 1 Ω
    1 - Body ground
    Pushed in
    10 kΩ or higher



NG
REPLACE PARKING BRAKE SWITCH ASSEMBLY (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - PARKING BRAKE SWITCH)

  1. C124797E03
    Disconnect the skid control ECU.

  1. Disconnect the parking brake switch connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    A4-28 (PKB) - E22-1
    Below 1 Ω
    A4-28 (PKB) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)

  1. C135297E01
    Disconnect the skid control ECU connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    A5-3 (BRL) - E13-31 (PKB)
    Below 1 Ω
    A5-3 (BRL) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT COMBINATION METER ASSEMBLY
  1. Check the combination meter system (Click here).

    OK:
    Combination meter is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)


← Brake Warning Light Remains ON (Jul 2007 – Jul 2009)Brake Warning Light Remains ON (Nov 2010 – Jul 2011) →