2011-2016 FJ Cruiser · Service Manual BRAKE

C1380 Stop Light Control Relay Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2012

Versions by build date: Nov 2010 – Jul 2012 from Aug 2012

DESCRIPTION

The skid control ECU inputs the stop light switch signal and detects the status of the brake operation.
DTC Code
DTC Detection Condition
Trouble Area
C1380
Either condition is met:
  1. When the voltage at the IG1 terminal is between 10 V and 14 V, the stop light driving output (STPO) is on, and a signal has not been input to the STP terminal for 5 seconds or more.
  2. When the voltage at the IG1 terminal is between 10 V and 14 V, the stop light driving output (STPO) is off, and the input signal at the STP terminal is different from the input signal at the STP2 terminal for 5 seconds or more.
  1. STOP fuse
  2. Harness or connector
  3. Stop light control relay (STOP LP)
  4. Master cylinder solenoid (Skid control ECU)

WIRING DIAGRAM

C212552E05

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first (Click here).


1. CHECK STOP LIGHT SWITCH OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

    OK:
    Stop light switch function is normal.



NG
Go to step 10
OK


2. INSPECT SKID CONTROL ECU (STP TERMINAL)

  1. C213546E14
    Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A4-7 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    A4-7 (STP) - Body ground
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK


3. INSPECT SKID CONTROL ECU (STP2 TERMINAL)

  1. C213546E17
    Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A4-45 (STP2) - Body ground
    Brake pedal depressed
    8 to 14 V
    A4-45 (STP2) - Body ground
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)
OK


4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Stop Light Relay
    Stop light relay
    Stop light relay ON or OFF
    Observe stop lights

  1. Check that the stop lights turn on and off on the rear combination light when using the tester.

OK:
The stop lights turn on and off according to the tester operations.



NG
Go to step 6
OK


5. RECONFIRM DTC

HINT:
Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

Result 
Result
Proceed to
DTC is output
A
DTC is not output
B


B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)

6. CHECK STOP LP CTRL RELAY

  1. C230328E01
    Remove the STOP LP CTRL relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Ignition switch ON
    8 to 14 V
    5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    STOP LP CTRL Relay Holder



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT STOP LP CTRL RELAY

  1. E149024E04
    Remove the STOP LP CTRL relay from the engine room R/B No. 2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Battery voltage not applied
    Below 1 Ω
    Battery voltage applied to terminal 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage not applied
    10 kΩ or higher
    Battery voltage applied to terminal 1 and 2
    Below 1 Ω

    Text in Illustration 
    *1
    STOP LP CTRL relay



NG
REPLACE STOP LP CTRL RELAY
OK


8. INSPECT SKID CONTROL ECU (STPO TERMINAL)

  1. C213546E16
    Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A4-16 (STPO) - Body ground
Ignition switch ON
11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Skid Control ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STPO CIRCUIT)
OK


9. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)

10. INSPECT STOP LP CTRL RELAY

  1. E149024E04
    Remove the STOP LP CTRL relay from the engine room R/B No. 2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Battery voltage not applied
    Below 1 Ω
    Battery voltage applied to terminal 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage not applied
    10 kΩ or higher
    Battery voltage applied to terminal 1 and 2
    Below 1 Ω

    Text in Illustration 
    *1
    STOP LP CTRL relay



NG
REPLACE STOP LP CTRL RELAY
OK

GO TO LIGHTING SYSTEM (PROBLEM SYMPTOMS TABLE)


← C1380 Stop Light Control Relay Malfunction (Nov 2010 – Jul 2012)C1380/64 Stop Light Control Relay Malfunction (Jul 2007 – Oct 2010) →