2011-2016 FJ Cruiser · Service Manual BRAKE

C1380/64 Stop Light Control Relay Malfunction

Diagnostic trouble codes · Vehicles built Jul 2007 – Oct 2010

DESCRIPTION

The skid control ECU inputs the stop light switch signal and detects the status of the brake operation.
DTC No.
DTC Detecting Conditions
Trouble Areas
C1380/64
Either of following conditions met when IG1 terminal voltage between 10 V and 14 V:
  1. Despite STPO (stop light driving output) being on, no signal input to STP terminal for 5 seconds or more
  2. Despite STPO being off, input signals of STP and STP2 do not match
  1. Stop light switch assembly
  2. Stop light switch circuit
  3. STOP LP CTRL relay
  4. Master cylinder solenoid (skid control ECU)

WIRING DIAGRAM

Click here.

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. CHECK STOP LIGHT SWITCH OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

    OK:
    Pedal Condition
    Illumination Condition
    Brake pedal depressed
    ON
    Brake pedal released
    OFF

    HINT:
    Check the stop light bulbs as they may have burnt out.



NG
CHECK STOP LIGHT SWITCH CIRCUIT
OK


2. INSPECT SKID CONTROL ECU TERMINAL VOLTAGE (STP)

  1. C121700E58
    Disconnect the skid control ECU connector.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Switch condition
    Specified Condition
    A4-7 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    A4-7 (STP) - Body ground
    Brake pedal released
    Below 1.5 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK


3. INSPECT SKID CONTROL ECU TERMINAL VOLTAGE (STP2)

  1. C121700E57
    Disconnect the skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    A4-7 (STP) - A4-45 (STP2)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)
OK


4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Select the following menu items: Chassis / ABS/VSC/TRC/ Active TestSelect the "Stop Light Relay" in the Active Test and operate the stop light relay using the intelligent tester.

    ACTIVE TEST: ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Stop Light Relay
    Stop light relay
    Stop light relay ON or OFF
    Observe stop lights

  1. Check that the stop lights turn on and off on the rear combination light when using the intelligent tester.

OK:
The stop lights turn on and off according to the intelligent tester operations.



NG
Go to step 6
OK


5. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID (Click here)

6. CHECK STOP LP CTRL RELAY

  1. F052358E01
    Disconnect the STOP LP CTRL relay.

  1. Turn the ignition switch to ON.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Terminal 5 - Body ground
    Always
    8 to 14 V
    Terminal 1 - Body ground
    Always
    8 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT STOP CTRL LP RELAY

  1. F052359E01
    Remove the STOP LP CTRL relay from the engine room R/B No. 2.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 4
    Below 1 Ω
    3 - 5
    10 kΩ or higher

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Battery voltage applied between terminals 1 (+) and 2 (-)
    10 kΩ or higher
    3 - 5
    Battery voltage applied between terminals 1 (+) and 2 (-)
    Below 1 Ω



NG
REPLACE STOP LP CTRL RELAY
OK


8. INSPECT SKID CONTROL ECU TERMINAL VOLTAGE (STPO)

  1. C121700E59
    Disconnect the skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage.

Standard voltage:
Tester Connection
Condition
Specified Condition
A4-16 (STPO) - Body ground
Brake pedal depressed
11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STPO CIRCUIT)
OK


9. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID (Click here)


← C1380 Stop Light Control Relay Malfunction (from Aug 2012)C1381 Acceleration Sensor Power Supply Voltage Malfunction (Nov 2010 – Jul 2011) →