2011-2016 FJ Cruiser · Service Manual BRAKE

C1241/41 Low Battery Positive Voltage

Diagnostic trouble codes · Vehicles built Jul 2007 – Oct 2010

DESCRIPTION

If there is a problem with the master cylinder solenoid (skid control ECU) power supply circuit, the skid control ECU outputs the DTC and prohibits operation under the fail-safe function.
If the voltage supplied to terminal IG1 is not within the DTC detection threshold due to malfunctions in parts such as the battery and generator circuit, this DTC is stored.
DTC No.
DTC Detecting Conditions
Trouble Areas
C1241/41
When either of following conditions detected:
1. Both of following conditions continue for at least 10 seconds.
  1. Vehicle speed more than 3 km/h (2 mph).
  2. IG1 terminal voltage less than 9.5 V.
2. All of following conditions continue for at least 0.2 seconds.
  1. Solenoid relay remains ON.
  2. IG1 terminal voltage less than 9.5 V.
  3. Relay contact open.
  1. Battery
  2. Charging system
  3. ECU-IG fuse
  4. Power source circuit
  5. Master cylinder solenoid (skid control ECU)

WIRING DIAGRAM

C164940E01

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V



NG
CHECK CHARGING SYSTEM (Click here)
OK


2. READ VALUE USING DATA LIST (IG VOLTAGE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Select the following menu items: Chassis / ABS/VSC/TRC/ Data List

    DATA LIST: ABS/VSC/TRC 
    Tester Display
    Measurement Item : Range
    Normal Condition
    Diagnostic Note
    ECU IG Power Voltage
    ECU power supply voltage : TOO LOW / NORMAL / TOO HIGH
    TOO HIGH: 14 V or more
    NORMAL: 9.5 V or 14V
    TOO LOW: Below 9.5 V
    -

  1. Measure the voltage output from the ECU displayed on the intelligent tester.

    OK:
    "Normal" is displayed.



NG
Go to step 4
OK


3. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of 3 km/h (2 mph) or more for 10 seconds or more.

  1. Check if the same DTC is detected (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID (Click here)

4. INSPECT FUSE (ECU-IG)

  1. C135286E01
    Remove the ECU-IG fuse from the driver side J/B.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


5. CHECK HARNESS AND CONNECTOR (GND TERMINAL CONTINUITY)

  1. C124799E03
    Disconnect the skid control ECU connectors.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    A4-1 (GND1) - Body ground
    Below 1 Ω
    A4-32 (GND2) - Body ground
    Below 1 Ω
    A5-4 (GND3) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)


← C1241 Low Power Supply Voltage Malfunction (from Aug 2012)C1242 Open Circuit in IG1/IG2 Power Source Circuit (Nov 2010 – Jul 2012) →