2011-2016 FJ Cruiser · Service Manual TRANSMISSION

P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014

DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.
DTC No.
DTC Detection Conditions
Trouble Areas
P0705
When any one of following conditions (A) to (C) is met (2-trip detection logic):
  1. (A) Any 2 or more of the following signals are ON simultaneously.
    1. NSW input signal is ON.
    2. R input signal is ON.
    3. D input signal is ON.
    4. 3 input signal is ON.
    5. 2 input signal is ON.
  1. (B) All switches are OFF simultaneously for P (NSW), R, N (NSW), D, 3 and 2 positions.
  2. (C) When NSW or R input signal is ON, 4 or L input signal is ON.
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. ECM

MONITOR DESCRIPTION

The DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the vehicle is in the P or N shift position.
When the park/neutral position switch sends more than one signal at a time from switch positions P, R, N, D, 3 or 2, the ECM interprets this as a fault in the switch. The ECM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C166892E02

INSPECTION PROCEDURE

HINT:
According to the Data List displayed on a intelligent tester, you can read the values of components, such as the switches, sensors and actuators, without removing any parts. Reading the Data List as a first step of troubleshooting is one method of shortening labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are for reference only. Do not depend solely on these reference values when judging whether a part is faulty or not.

  1. Turn the ignition switch to OFF.
  2. Connect the intelligent tester to the DLC3.
  3. Turn the ignition switch to ON.
  4. Turn the tester ON.
  5. Enter the following menus: Powertrain / Engine and ECT / Data List.
  6. According to the display on the tester, read the Data List.
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP Switch Status/
    ON or OFF
    Shift lever position is:
    P or N: ON
    Except P and N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW Status (R Range)
    PNP Switch Status/
    ON or OFF
    Shift lever position is:
    R: ON
    Except R: OFF
    Shift SW Status (D Range)
    PNP Switch Status/
    ON or OFF
    Shift lever position is:
    D or 4: ON
    Except D and 4: OFF
    Shift SW Status (4 Range)
    PNP Switch Status/
    ON or OFF
    Shift lever position is:
    4: ON
    Except 4: OFF
    Shift SW Status (3 Range)
    PNP Switch Status/
    ON or OFF
    Shift lever position is:
    3: ON
    Except 3: OFF
    Shift SW Status (2 Range)
    PNP Switch Status/
    ON or OFF
    Shift lever position is:
    2 or L: ON
    Except 2 and L: OFF
    Shift SW Status (L Range)
    PNP Switch Status/
    ON or OFF
    Shift lever position is:
    L: ON
    Except L: OFF

1. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C130119E05
    Disconnect the park/neutral position switch connector.

  1. Measure the resistance when the shift lever is moved to each position.

Standard resistance:
Shift Position
Tester Connection
Specified Condition
P or N
4 (B) - 5 (L)
Below 1 Ω
Except P and N
4 (B) - 5 (L)
10 kΩ or higher
R
1 (RL) - 2 (RB)
Below 1 Ω
Except R
1 (RL) - 2 (RB)
10 kΩ or higher
D or 4
2 (RB) - 7 (DL)
Below 1 Ω
Except D and 4
2 (RB) - 7 (DL)
10 kΩ or higher
3
2 (RB) - 3 (2L)
Below 1 Ω
Except 3
2 (RB) - 3 (2L)
10 kΩ or higher
2 or L
2 (RB) - 8 (LL)
Below 1 Ω
Except 2 and L
2 (RB) - 8 (LL)
10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


2. INSPECT SHIFT LOCK CONTROL ECU SUB-ASSEMBLY

  1. D029380E11
    Connect the park/neutral position switch connector.

  1. Disconnect the shift lock control ECU connector.

  1. Measure the resistance when the shift lever is moved to each position.

Standard resistance:
Shift Position
Tester Connection
Specified Condition
D
9 (NSSD) - 3 (MT4)
10 kΩ or higher
4
9 (NSSD) - 3 (MT4)
Below 1 Ω
2
10 (NSSL) - 4 (MTL)
10 kΩ or higher
L
10 (NSSL) - 4 (MTL)
Below 1 Ω



NG
REPLACE SHIFT LOCK CONTROL ECU SUB-ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

  1. G100772E03
    Connect the shift lock control ECU connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage when the shift lever is moved to each position.

    Standard voltage:
    Shift Position
    Tester Connection
    Specified Condition
    P or N
    B2-8 (NSW) - B3-1 (E1)
    Below 2 V
    Except P and N
    B2-8 (NSW) - B3-1 (E1)
    11 to 14 V
    R
    E46-11 (R) - B3-1 (E1)
    11 to 14 V*
    Except R
    E46-11 (R) - B3-1 (E1)
    Below 1 V
    D or 4
    E46-21 (D) - B3-1 (E1)
    11 to 14 V
    Except D and 4
    E46-21 (D) - B3-1 (E1)
    Below 1 V
    4
    E46-20 (4) - B3-1 (E1)
    11 to 14 V
    Except 4
    E46-20 (4) - B3-1 (E1)
    Below 1 V
    3
    E46-19 (3) - B3-1 (E1)
    11 to 14 V
    Except 3
    E46-19 (3) - B3-1 (E1)
    Below 1 V
    2 or L
    E46-10 (2) - B3-1 (E1)
    11 to 14 V
    Except 2 and L
    E46-10 (2) - B3-1 (E1)
    Below 1 V
    L
    E46-9 (L) - B3-1 (E1)
    11 to 14 V
    Except L
    E46-9 (L) - B3-1 (E1)
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to illumination of the back up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← DIAGNOSTIC TROUBLE CODE CHART (from Aug 2014)P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (Aug 2009 – Oct 2010) →