2011-2016 FJ Cruiser · Service Manual TRANSMISSION

P0756 Shift Solenoid "B" Performance (Shift Solenoid Valve S2)

Diagnostic trouble codes · Vehicles built Dec 2007 – Jul 2009

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 from Aug 2009

DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).
DTC No.
DTC Detection Condition
Trouble Area
P0756
S2 stuck ON malfunction:
The ECM determines that there is a malfunction when the following conditions are met (2-trip detection logic*1, 1-trip detection logic*2):
  1. (a) When the ECM directs the gearshift to switch to 1st gear, the actual gear is shifted to 2nd.
  2. (b) When the ECM directs the gearshift to switch to 5th gear, the engine overruns (clutch slips).
  1. Shift solenoid valve S2 remains open
  2. Valve body is blocked
  3. Automatic transmission (clutch, brake or gear, etc.)
S2 stuck OFF malfunction:
The ECM determines that there is a malfunction when the following conditions are met (2-trip detection logic*1, 1-trip detection logic*2):
  1. (a) When the ECM directs the gearshift to switch to 1st gear, the actual gear is also shifted to 1st.
  2. (b) When the ECM directs the gearshift to switch to 2nd gear, the actual gear is shifted to 1st.
  3. (c) When the ECM directs the gearshift to switch to 5th gear, the actual gear is also shifted to 5th.
  1. Shift solenoid valve S2 remains closed
  2. Valve body is blocked
  3. Automatic transmission (clutch, brake or gear, etc.)

HINT:
  1. *1: w/ OBD
  2. *2: w/o OBD


MONITOR DESCRIPTION

This DTC indicates "stuck ON malfunction" or "stuck OFF malfunction" of the shift solenoid valve S2. The ECM controls the gearshifts by turning the shift solenoid valves "ON/OFF". When the gear position directed by the ECM and the actual gear position do not match, the ECM stores the DTC.

INSPECTION PROCEDURE

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the tester ON.
  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.
  7. According to the display on the tester, perform the Active Test.

HINT:
While driving, the shift position can be changed with the intelligent tester.
Comparing the shift position directed by the Active Test with the actual shift position enables the problem to be confirmed (Click here).
Tester Display
Test Part
Control Range
Diagnostic Note
Control the Shift Position
Operate shift solenoid valve and set each shift position by yourself
  1. Press "→" button: Shift up
  2. Press "←" button: Shift down
Possible to check operation of shift solenoid valves
[Vehicle Condition]
50 km/h (30 mph) or less

HINT:
  1. This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
  2. The 4th to 5th up-shifting must be performed with the accelerator pedal released.
  3. The 5th to 4th down-shifting must be performed with the accelerator pedal released.
  4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
  5. The shift position directed by the ECM is shown in the Data List/Shift Status display on the intelligent tester.
  6. The shift solenoid valve S2 is turned on/off normally when the shift lever is in D:
    Gearshift controlled by ECM
    1st
    2nd
    3rd
    4th
    5th
    Shift solenoid valve S2
    OFF
    ON
    ON
    OFF
    OFF


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0756)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the intelligent tester.

    Result 
    Result
    Proceed to
    Only "P0756" is output
    A
    "P0756" and other DTCs are output
    B

    HINT:
    If any codes besides "P0756" are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)
G020657E01

NOTICE:
  1. Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F).
  2. Be careful to prevent SST hose from interfering with the exhaust pipe.
  3. Perform the test with the A/C OFF.

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. According to the display on the tester, perform the Active Test.

  1. Measure the line pressure with SST.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Active the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Active the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    *: Active the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.

    OK:
    The line pressure changes as specified when performing the Active Test.



NG
REPLACE SHIFT SOLENOID VALVE SLT (Click here)
OK


3. INSPECT SHIFT SOLENOID VALVE S2

  1. A110987E13
    Remove the shift solenoid valve S2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Solenoid Connector (S2) - Solenoid Body (S2)
    20°C (68°F)
    11 to 15 Ω

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE S2 (Click here)
OK


4. INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    OK:
    There are no foreign objects on any valves and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)


← P0756 Shift Solenoid "B" Performance (Shift Solenoid Valve S2) (Jul 2007 – Nov 2007)P0756 Shift Solenoid "B" Performance (Shift Solenoid Valve S2) (from Aug 2009) →