2011-2016 FJ Cruiser · Service Manual TRANSMISSION

P0781 1-2 Shift (1-2 Shift Valve)

Diagnostic trouble codes · Vehicles built Jul 2007 – Nov 2007

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 from Aug 2009

DESCRIPTION

A110990E03
The 1-2 shift valve performs shifting to 1st gear and other gears.
DTC No.
DTC Detection Conditions
Trouble Areas
P0781
1-2 shift valve malfunction:
The ECM determines that there is a malfunction when the following conditions (a) and (b), or (a) and (c) are met (1-trip detection logic):
  1. (a) When the ECM directs the gearshift to switch to 2nd gear, the actual gear is shifted to 1st.
  2. (b) When the ECM directs the gearshift to switch to 4th gear, the actual gear is shifted to 3rd.
  3. (c) When the ECM directs the gearshift to switch to 5th gear, the engine overruns (clutch slips)
  1. Valve body is blocked up or stuck (1-2 shift valve)
  2. Shift solenoid valve SLT remains open or closed
  3. Automatic transmission (clutch, brake or gear, etc.)

HINT:
Gear positions in the event of a 1-2 shift valve mechanical problem:

Gearshift controlled by ECM
1st
2nd
3rd
4th
5th
Actual gear position under malfunction
1st
1st
3rd
3rd
N*
N*: Neutral

MONITOR DESCRIPTION

This DTC indicates that the 1-2 shift valve in the valve body is locked in the direction of the spring compression. The ECM controls the gearshifts by turning the shift solenoid valves "ON/OFF" and switching oil pressure to the valves in the valve body.
The ECM calculates the "actual" transmission gear by comparing the signals from the input speed sensor (NT) and the output speed sensor (SP2). The ECM can detect many mechanical problems in the shift solenoids, valve body, and the transmission clutches, brakes, and gears. If the ECM detects that the actual gear position and the commanded gear position are different, the ECM store the DTC .

INSPECTION PROCEDURE


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0781)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the intelligent tester.

    Result: 
    Display (DTC Output)
    Proceed to
    Only "P0781" is output
    A
    "P0781" and other DTCs
    B

    HINT:
    If any codes besides "P0781" are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT)

HINT:
Performing the Active Test using a intelligent tester allows components, such as the relay, VSV, and actuator, to be operated without removing any parts. Performing the Active Test as a first step of troubleshooting is one method of shortening labor time.
It is possible to display the Data List during the Active Test.
  1. Warm up the engine.
  2. Turn the ignition switch to OFF.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the tester ON.
  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.
  7. According to the display on the tester, perform the Active Test.

HINT:
While driving, the shift position can be changed with the intelligent tester.
Comparing the shift position directed by the Active Test with the actual shift position enables the problem to be confirmed (Click here).

Tester Display
Test Part
Control Range
Diagnostic Note
Control the Shift Position
Operate shift solenoid valve and set each shift position by yourself
  1. Press "→" button: Shift up
  2. Press "←" button: Shift down
Possible to check operation of shift solenoid valves
[Vehicle Condition]
50 km/h (30 mph) or less

HINT:
  1. This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
  2. The 4th to 5th up-shifting must be performed with the accelerator pedal released.
  3. The 5th to 4th down-shifting must be performed with the accelerator pedal released.
  4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
  5. The shift position directed by the ECM is shown in the Data List / Shift Status display on the intelligent tester.
  6. Gear positions in the event of a solenoid valve mechanical problem:
    Gearshift operated by tester
    1st
    2nd
    3rd
    4th
    5th
    Actual gear position under malfunction
    1st
    1st
    3rd
    3rd
    N*
    N*: Neutral

    OK:
    Gear position changes in accordance with the tester operation.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)
G020657E01

NOTICE:
  1. Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F).
  2. Be careful to prevent SST's hose from interfering with the exhaust pipe.
  3. Perform the test with the A/C OFF.

HINT:
Performing a intelligent tester Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.
The Data List can be displayed during the Active Test.

  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect a intelligent tester to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. According to the display on the tester, perform the Active Test.

  1. Measure the line pressure with SST.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Active the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Active the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    *: Active the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well. Please note that the pressure values in the Active Test and HYDRAULIC TEST are different.



NG
REPLACE SHIFT SOLENOID VALVE SLT (Click here)
OK


4. CLEAR DTC AND PERFORM RUNNING TEST
  1. Clear the DTC, and check for the DTC again after conducting the "MONITOR DRIVE PATTERN FOR ECT TEST" (Click here).

    OK:
    No DTC



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

END


← P0778 Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2) (from Aug 2009)P0781 1-2 Shift (1-2 Shift Valve) (Dec 2007 – Jul 2009) →