2011-2016 FJ Cruiser · Service Manual BRAKE

C1268/68 Transfer "L4" Position Switch Circuit

Diagnostic trouble codes · Vehicles built Aug 2009 – Oct 2010

Also covers:

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010

DESCRIPTION

A-TRC is activated if wheel skid is detected while the transfer is in the L4 position.
DTC No.
DTC Detection Condition
Trouble Area
C1268/68
When either of the following conditions is met:
  1. Open circuit detected between the Skid Control ECU and ECM terminals (between EXI and L4).
  2. Open circuit detected between the Skid Control ECU and 4WD ECU terminals (between EXI and 4WD).
  3. Open circuit detected between the Skid Control ECU terminals (between EXI and HDCS).
  4. Open circuit detected between the Skid Control ECU and GND (NEO) terminals.
  1. ECM
  2. 4WD control ECU (Rear Diff, Lock)
  3. Master cylinder solenoid (Skid Control ECU)
  4. Wire harness or connector
C1283/83
Detected only during test mode
Master cylinder solenoid (Skid Control ECU)

WIRING DIAGRAM

C218838E02
C218839E01

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. CHECK HARNESS AND CONNECTOR (NEO TERMINAL)
  1. Disconnect the A4 skid control ECU connector.

  1. C213546E09
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-10 (NEO) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT SKID CONTROL ECU (EXI TERMINAL VOLTAGE)

  1. C213546E11
    Disconnect the A4 skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Transfer Condition
    Specified Condition
    A4-27 (EXI) - Body ground
    L4
    Below 1.5 V
    A4-27 (EXI) - Body ground
    Other than above
    8 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Skid Control ECU)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for A/T w/ Rear Diff Lock)
    B
    NG (for A/T w/o Rear Diff Lock)
    C
    NG (for M/T w/ Rear Diff Lock)
    D
    NG (for M/T w/o Rear Diff Lock)
    E



B
Go to step 4

C
Go to step 5

D
Go to step 6

E
Go to step 7
A


3. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTC is recorded (Click here).

    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)

4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ECM, 4WD CONTROL ECU (READ DIFF LOCK))
  1. Disconnect the A4 skid control ECU connector.

  1. Disconnect the transfer indicator switch (for L4 position) connector.

  1. Disconnect the ECM connector.

  1. Disconnect the 4WD CONTROL ECU (Rear Diff, Lock) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-27 (EXI) - E82-16 (L4)
    Always
    Below 1 Ω
    A4-27 (EXI) - L7-8 (4WD)
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 8
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ECM)
  1. Disconnect the A4 skid control ECU connector.

  1. Disconnect the transfer indicator switch (for L4 position) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-27 (EXI) - E82-16 (L4)
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 9
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

6. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4WD CONTROL ECU (REAR DIFF LOCK))
  1. Disconnect the A4 skid control ECU connector.

  1. Disconnect the transfer indicator switch (for L4 position) connector.

  1. Disconnect the 4WD CONTROL ECU (Rear Diff, Lock) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-27 (EXI) - L7-8 (4WD)
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 8
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU)
  1. Disconnect the A4 skid control ECU connector.

  1. Disconnect the transfer indicator switch (for L4 position) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-27 (EXI) - A4-44 (HDCS)
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

8. REPLACE 4WD CONTROL ECU (REAR DIFF, LOCK)
  1. Replace the 4WD CONTROL ECU (Rear Diff, Lock).

  1. Clear the DTCs.

  1. Check if the same DTC is recorded.

    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
Go to step 9
A

END

9. REPLACE ECM
  1. Replace the ECM (Click here).

  1. Clear the DTCs.

  1. Check if the same DTC is recorded.

    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

END


← C1268/68 Transfer "L4" Position Switch Circuit (+ C1283/83) (Jul 2007 – Jul 2009)C1282 Center Differential Lock Position Switch (Nov 2010 – Jul 2012) →