C1282 Center Differential Lock Position Switch
Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012
Versions by build date: Nov 2010 – Jul 2012 from Aug 2012
DESCRIPTION
This circuit monitors whether the transfer is in 2WD or 4WD mode and inputs the signal to the skid control ECU.In 2WD mode, TRC is activated.
In 4WD mode, A-TRC is activated.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1282 |
Detected only during test mode |
|
- *1: for Automatic Transmission
- *2: for Manual Transmission
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- When replacing the master cylinder solenoid, perform zero point calibration (Click here).
| 1. INSPECT SKID CONTROL ECU TERMINAL VOLTAGE (EXI4) |
Disconnect the skid control ECU connector.

Turn the ignition switch to ON.
for Automatic Transmission
Move the transfer high and low shift lever to the H2, H4, and L4 ranges, and measure the voltages in each range.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Transfer Condition
Specified Condition
A4-29 (EXI4) - Body ground
H2
8 to 14 V
A4-29 (EXI4) - Body ground
H4, L4
Below 1.5 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU)
for Manual Transmission
Move the transfer high and low shift lever to the H, HL, and LL ranges, and measure the voltages in each range.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Transfer Condition
Specified Condition
A4-29 (EXI4) - Body ground
H
8 to 14 V
A4-29 (EXI4) - Body ground
HL, LL
Below 1.5 V
| Result |
Proceed to |
| OK |
A |
| NG (for automatic transmission) |
B |
| NG (for manual transmission) |
C |
|
|
||||
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (NEO TERMINAL - BODY GROUND) |
Disconnect the skid control ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Vehicle Drive Train
Specified Condition
A4-43 (NEO) - Body ground
4WD
Below 1 Ω
|
|
||||
| OK | |
| 3. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | ||
| ||
| 4. INSPECT TRANSFER INDICATOR SWITCH (4WD position) |
Disconnect the transfer indicator switch (4WD position) connector.

Remove the transfer indicator switch (4WD position).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Pushed
Below 1 Ω
1 - 2
Released
10 kΩ or higher
Text in Illustration *a
Component without harness connected
(Transfer Indicator Switch (for 4WD position))
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - TRANSFER INDICATOR SWITCH) |
Disconnect the four wheel drive control ECU connector.
Disconnect the transfer indicator switch (4WD position) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B60-6 (4WD) - B39-2
Always
Below 1 Ω
B60-6 (4WD) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FOUR WHEEL DRIVE CONTROL ECU) |
Disconnect the skid control ECU connector.
Disconnect the 4WD control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A4-29 (EXI4) - B60-8 (ADD)
Always
Below 1 Ω
A4-29 (EXI4) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. REPLACE 4 WHEEL DRIVE CONTROL ECU NO.2 |
Replace the four wheel drive control ECU.
| NEXT | |
| 8. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | ||
| ||
| 9. INSPECT TRANSFER INDICATOR SWITCH (CENTER DIFFERENTIAL LOCK POSITION) |
Disconnect the transfer indicator switch (center differential lock position) connector.

Remove the transfer indicator switch (center differential lock position).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Pushed
Below 1 Ω
1 - 2
Released
10 kΩ or higher
Text in Illustration *a
Component without harness connected
(Transfer Indicator Switch (center differential lock position))
|
|
||||
| OK | |
| 10. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TRANSFER INDICATOR SWITCH) |
Disconnect the skid control ECU connector.
Disconnect the transfer indicator switch (center differential lock position) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A4-29 (EXI4) - B43-2
Always
Below 1 Ω
A4-29 (EXI4) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 11. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | ||
| ||
