2011-2016 FJ Cruiser · Service Manual BRAKE

C1282 Center Differential Lock Position Switch

Diagnostic trouble codes · Vehicles built from Aug 2012

Versions by build date: Nov 2010 – Jul 2012 from Aug 2012

DESCRIPTION

This circuit monitors whether the transfer is in 2WD or 4WD mode and inputs the signal to the skid control ECU.
In 2WD mode, TRC is activated.
In 4WD mode, A-TRC is activated.
DTC Code
DTC Detection Condition
Trouble Area
C1282
Detected only during test mode
  1. Transfer indicator switch (4WD position)*1
  2. Transfer indicator switch (4WD position) circuit*1
  3. Transfer indicator switch (center differential lock position)*2
  4. Transfer indicator switch (center differential lock position) circuit*2
  1. *1: for Automatic Transmission
  2. *2: for Manual Transmission

WIRING DIAGRAM

C164943E03
C164944E02

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. INSPECT SKID CONTROL ECU TERMINAL VOLTAGE (EXI4)

  1. C213546E13
    Disconnect the skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. for Automatic Transmission

    1. Move the transfer high and low shift lever to the H2, H4, and L4 ranges, and measure the voltages in each range.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Transfer Condition
      Specified Condition
      A4-29 (EXI4) - Body ground
      H2
      8 to 14 V
      A4-29 (EXI4) - Body ground
      H4, L4
      Below 1.5 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Skid Control ECU)

  1. for Manual Transmission

    1. Move the transfer high and low shift lever to the H, HL, and LL ranges, and measure the voltages in each range.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Transfer Condition
      Specified Condition
      A4-29 (EXI4) - Body ground
      H
      8 to 14 V
      A4-29 (EXI4) - Body ground
      HL, LL
      Below 1.5 V

Result 
Result
Proceed to
OK
A
NG (for automatic transmission)
B
NG (for manual transmission)
C


B
Go to step 4

C
Go to step 9
A


2. CHECK HARNESS AND CONNECTOR (NEO TERMINAL - BODY GROUND)

  1. C213546E12
    Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Vehicle Drive Train
    Specified Condition
    A4-43 (NEO) - Body ground
    4WD
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID (Click here)

4. INSPECT TRANSFER INDICATOR SWITCH (4WD position)

  1. G034535E05
    Disconnect the transfer indicator switch (4WD position) connector.

  1. Remove the transfer indicator switch (4WD position).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pushed
    Below 1 Ω
    1 - 2
    Released
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transfer Indicator Switch (for 4WD position))



NG
REPLACE TRANSFER INDICATOR SWITCH (4WD POSITION) (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - TRANSFER INDICATOR SWITCH)
  1. Disconnect the four wheel drive control ECU connector.

  1. Disconnect the transfer indicator switch (4WD position) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B60-6 (4WD) - B39-2
    Always
    Below 1 Ω
    B60-6 (4WD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FOUR WHEEL DRIVE CONTROL ECU)
  1. Disconnect the skid control ECU connector.

  1. Disconnect the 4WD control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-29 (EXI4) - B60-8 (ADD)
    Always
    Below 1 Ω
    A4-29 (EXI4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. REPLACE 4 WHEEL DRIVE CONTROL ECU NO.2
  1. Replace the four wheel drive control ECU.


NEXT


8. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID (Click here)

9. INSPECT TRANSFER INDICATOR SWITCH (CENTER DIFFERENTIAL LOCK POSITION)

  1. G034535E05
    Disconnect the transfer indicator switch (center differential lock position) connector.

  1. Remove the transfer indicator switch (center differential lock position).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pushed
    Below 1 Ω
    1 - 2
    Released
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transfer Indicator Switch (center differential lock position))



NG
REPLACE TRANSFER INDICATOR SWITCH (CENTER DIFFERENTIAL LOCK POSITION) (Click here)
OK


10. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TRANSFER INDICATOR SWITCH)
  1. Disconnect the skid control ECU connector.

  1. Disconnect the transfer indicator switch (center differential lock position) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-29 (EXI4) - B43-2
    Always
    Below 1 Ω
    A4-29 (EXI4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID (Click here)


← C1282 Center Differential Lock Position Switch (Nov 2010 – Jul 2012)C1290 Steering Angle Sensor Zero Point Malfunction (Nov 2010 – Jul 2012) →