No Answer-Back
Circuit diagnosis · Vehicles built Jul 2007 – Oct 2010
Versions by build date: Jul 2007 – Oct 2010 from Nov 2010
DESCRIPTION
In this case, wireless control functions are normal but the hazard warning light or wireless door lock buzzer answer-back function does not operate.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS |
 |
Check the wireless door lock functions by operating the transmitter switches.
Result
Result
|
Proceed to
|
Wireless door lock functions are normal
|
A
|
Wireless door lock functions are abnormal
|
B
|
|
B |
 |
|
|
|
| A |
|
 |
|
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (WIRELESS DOOR LOCK BUZZER, FLASHER RELAY) |
 |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Body Electrical / Main Body / Active Test.
According to the display on the tester, perform the Active Test.
- Main Body:
Tester Display
|
Test Part
|
Control Range
|
Diagnostic Note
|
Hazard
|
Flasher relay
|
ON or OFF
|
-
|
Wireless Buzzer*1
|
Sounds wireless buzzer
|
ON or OFF
|
-
|
Result
Result
|
Proceed to
|
Hazard warning light answer-back function does not operate
|
A
|
Wireless door lock buzzer answer-back function does not operate*1
|
B
|
Hazard warning light and wireless door lock buzzer*1 answer-back function operate normally
|
C
|
- *1: w/ Wireless door lock buzzer
|
B |
 |
|
|
|
|
C |
 |
|
|
|
| A |
|
 |
|
| 3. CHECK HAZARD WARNING LIGHTS |
 |
Check that the hazard warning lights flash when the hazard warning signal switch is pressed.
- OK:
- Hazard warning lights flash when hazard warning signal switch is pressed.
|
NG |
 |
|
|
|
| OK |
|
 |
|
|
| 4. CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU) |
 |
- Disconnect the A12 wireless door lock buzzer connector.
Disconnect the 1B main body ECU connector.
Measure the resistance.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
1B-10 (BZR) - A12-1
|
Always
|
Below 1 Ω
|
1B-6 (BZR2) - A12-2
|
Always
|
Below 1 Ω
|
1B-10 (BZR) orA12-1 - Body ground
|
Always
|
10 kΩ or higher
|
1B-6 (BZR2) or A12-2 - Body ground
|
Always
|
10 kΩ or higher
|
Reconnect the buzzer connector.
Reconnect the main body ECU connector.
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 5. REPLACE WIRELESS DOOR LOCK BUZZER |
 |
Temporarily replace the wireless door lock buzzer with a new or normally functioning one (Click here).
Check that the buzzer sounds when using the transmitter LOCK and UNLOCK switches.
- OK:
- The buzzer sounds.
- NOTICE:
- When battery voltage is directly applied to the buzzer, the buzzer does not sound.
- HINT:
- The buzzer circuit is built into the main body ECU, not into the buzzer itself.
|
NG |
 |
|
|
|
| OK |
|
 |
|
| END (WIRELESS DOOR LOCK BUZZER IS DEFECTIVE) |
|