2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Back-up Light Circuit

Circuit diagnosis · Vehicles built from Jul 2007

DESCRIPTION

Automatic Transmission models: The park / neutral position switch turns on when the shift lever is moved into the R position, causing the back-up lights to illuminate.
Manual Transmission models: The back-up light switch turns on when the shift lever is moved into the R position, causing the back-up lights to illuminate.

WIRING DIAGRAM

E148425E02

INSPECTION PROCEDURE


1. INSPECT FUSE (IG1)
  1. Remove the IG1 fuse from the main body ECU.

  1. Measure the resistance according value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Connection
    IG1 fuse
    Always
    Below 1 Ω

  1. Reinstall the IG1 fuse.



NG
REPLACE FUSE
OK


2. INSPECT BULB (BACK-UP LIGHT BULB)
B141591E01
  1. Remove the back-up light bulb.

  1. Apply battery voltage to the terminals and check that the back-up light illuminates.

    OK:
    Measurement Condition
    Specified Connection
    Positive battery - Terminal 1
    Negative battery - Terminal 2
    back-up light illuminates

  1. Reinstall the back-up light bulb.



NG
REPLACE BULB (Click here)
OK


3. CHECK TRANSAXLE TYPE
  1. Check the vehicle's transaxle type.

    Result:
    Transaxle Type
    Proceed To
    Automatic Transmission
    A
    Manual Transmission
    B



B
Go to step 7
A


4. INSPECT PARK / NEUTRAL POSITION SWITCH

  1. C110340E33
    Disconnect the B35 park / neutral position switch.

  1. Measure the resistance according value(s) in the table below.

    Standard resistance:
    Tester Connection
    Shift Position
    Specified Connection
    2 (RB) - 1 (RL)
    R
    Below 1 Ω
    2 (RB) - 1 (RL)
    Except R
    10 kΩ or higher

  1. Reconnect the park / neutral position switch.



NG
REPLACE PARK / NEUTRAL POSITION SWITCH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (FUSE - PARK / NEUTRAL POSITION SWITCH)

  1. B124048E07
    Disconnect the B35 park / neutral position switch connector.

  1. Measure the voltage according value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    B35-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Reconnect the park / neutral position switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (PARK / NEUTRAL POSITION SWITCH - REAR BACK-UP LIGHT)

  1. B138183E01
    Disconnect the B35 park / neutral position switch connector.

  1. Disconnect the L13 and L16 back-up light connectors.

  1. Measure the resistance according value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B35-1 (RL) - L13-1
    Always
    Below 1 Ω
    B35-1 (RL) - L16-1
    Always
    Below 1 Ω
    L13-1 - Body ground
    Always
    10 kΩ or higher
    L16-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the park / neutral position switch connector.

  1. Reconnect the back-up light connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BACK-UP LIGHT - BODY GROUND)

7. INSPECT BACK-UP LIGHT SWITCH

  1. B135322E03
    Disconnect the B42 back-up light switch connector.

  1. Measure the resistance according value(s) in the table below.

    Standard resistance:
    Tester Connection
    Shift Position
    Specified Connection
    1 - 2
    R
    Below 1 Ω
    1 - 2
    Except R
    10 kΩ or higher

  1. Reconnect the back-up light switch connector.



NG
REPLACE BACK-UP LIGHT SWITCH (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (FUSE - BACK-UP LIGHT SWITCH)

  1. B135323E02
    Disconnect the B42 back-up light switch connector.

  1. Measure the voltage according value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    B42-2 - Body ground
    Ignition switch ON
    11 to 14 V

  1. Reconnect the back-up light switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH - BACK-UP LIGHT)

  1. B138184E01
    Disconnect the B42 back-up light switch connector.

  1. Disconnect the L13 and L16 back-up light connectors.

  1. Measure the resistance according value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B42-1 - L13-1
    Always
    Below 1 Ω
    B42-1 - L16-1
    Always
    Below 1 Ω
    L13-1 - Body ground
    Always
    10 kΩ or higher
    L16-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the back-up light switch connector.

  1. Reconnect the back-up light connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BACK-UP LIGHT - BODY GROUND)


← Hazard Warning Switch Circuit (from Nov 2010)Light Control Switch Circuit (Jul 2007 – Oct 2010) →