INSTALLATION
Removal / installation · Vehicles built from Nov 2012
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 Aug 2012 – Oct 2012 from Nov 2012
| 1. INSTALL NO. 4 FUEL TANK BAND BRACKET (for Double Tank Type) |
for LH Side:
Install the No. 4 fuel tank band bracket with the 4 bolts.
- Torque:
- 40 N*m{ 408 kgf*cm , 30 ft.*lbf }
Engage the 3 clamps and connect the wire harness.
for RH Side:
Install the No. 4 fuel tank band bracket with the 4 bolts.
- Torque:
- 40 N*m{ 408 kgf*cm , 30 ft.*lbf }
| 2. INSTALL FUEL SUB TANK SUB-ASSEMBLY (for Double Tank Type) |
| 3. INSTALL REAR BUMPER SIDE SUPPORT SUB-ASSEMBLY LH (for Single Tank Type) |
Align the 2 locating guides with the hole and install the rear bumper side support sub-assembly LH with the 2 bolts.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Engage the clamp and connect the wire harness.
| 4. INSTALL REAR BUMPER SIDE SUPPORT SUB-ASSEMBLY RH (for Single Tank Type) |
Align the 2 locating guides with the hole and install the rear bumper side support sub-assembly RH with the 2 bolts.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
| 5. INSTALL REAR BUMPER BAR BRACKET LH |
Install the rear bumper bar bracket LH with the 2 bolts.
- Torque:
- 31 N*m{ 316 kgf*cm , 23 ft.*lbf }
| 6. INSTALL REAR BUMPER BAR BRACKET RH |
Install the rear bumper bar bracket RH with the 2 bolts.
- Torque:
- 31 N*m{ 316 kgf*cm , 23 ft.*lbf }
| 7. INSTALL REAR BUMPER SIDE STAY LH |
Insert the hook into the body hole and install the rear bumper side stay LH with the bolt.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
| 8. INSTALL REAR BUMPER SIDE STAY RH |
- HINT:
- Use the same procedure as for the LH side.
| 9. INSTALL REAR BUMPER ENERGY ABSORBER |
Install the rear bumper energy absorber.
| 10. INSTALL REAR BUMPER UPPER RETAINER LH |
Engage the 3 claws and install the rear bumper upper retainer LH.
Install the 2 screws.
- Torque:
- 3.0 N*m{ 31 kgf*cm , 27 in.*lbf }
| 11. INSTALL REAR BUMPER UPPER RETAINER RH |
- HINT:
- Use the same procedure as for the LH side.
| 12. INSTALL REAR BUMPER END RETAINER LH |
Engage the 2 claws and install the rear bumper end retainer LH.
Install the screw.
- Torque:
- 3.0 N*m{ 31 kgf*cm , 27 in.*lbf }
| 13. INSTALL REAR BUMPER END RETAINER RH |
- HINT:
- Use the same procedure as for the LH side.
| 14. INSTALL REAR BUMPER COVER |
Engage the 6 claws and the 2 clips and install the rear bumper cover.
Engage the wire harness clamp, and connect the connector.
Install the 7 bolts and the 2 screws.

Text in Illustration *1
Bolt A
*2
Bolt B
*3
Screw
- Torque:
- for bolt A:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
- for bolt B:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
- for screw:
- 3.0 N*m{ 31 kgf*cm , 27 in.*lbf }
Install the clip.
Remove the protective tape.
