2011-2016 FJ Cruiser · Service Manual BRAKE

C0200/31 Front Speed Sensor RH Circuit

Diagnostic trouble codes · Vehicles built Jul 2007 – Oct 2010

Also covers:

DESCRIPTION

The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU. Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change as the rotors turn.
The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU. The ECU monitors the wheel speeds through these pulse signals to control the ABS system.
C135276E02
DTC No.
DTC Detecting Conditions
Trouble Areas
C0200/31
C0205/32
When any one of following conditions met:
  1. At vehicle speed of 10 km/h (6 mph) or more, speed sensor signal circuit open or short for 1 second or more.
  2. Speed sensor signal open circuit occurs at least 255 times.
  3. Speed sensor signal circuit open for 0.5 seconds or more.
  4. With ignition switch to ON and vehicle speed at 3 km/h (2 mph) or more, 3 wheels output reverse rotation signals and 1 wheel outputs high-frequency pulse 75 times.
  5. At vehicle speed of 10 km/h (6 mph) or more, speed sensor output halves for 5 seconds.
  6. At vehicle speed of 10 km/h (6 mph) or more, changing of normal rotation signal and reverse rotation signal occurs 7 times within 0.006 seconds while ignition switch to ON.
  7. Signal output of any one wheel different from signals of other 3 wheels for 1 second, at vehicle speed of 30 km/h (18 mph) or more.
  8. Reverse rotation signal produced for 1 second or more at vehicle speed of 100 km/h (62 mph) or more.
  9. At vehicle speed of 30 km/h (18 mph) or more, one speed sensor malfunctions and differs in signal direction from other 3 wheels.
  10. When voltage at IG1 terminal 9.5 V or more, voltage of sensor power supply decreases for 0.5 seconds or more.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation
  4. Skid control sensor wire
  5. Master cylinder solenoid (skid control ECU)
C1235/35
C1236/36
When either of following conditions (1 or 2) detected:
  1. At vehicle speed of 20 km/h (12 mph) or more, noise in speed sensor signal continues for 5 seconds or more.
  2. At vehicle speed of 10 km/h (6 mph) or more, noise detected as rotor turns, for 15 seconds or more.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Master cylinder solenoid (skid control ECU)
C1271/71
C1272/72
Detected only during test mode.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation
  4. Skid control sensor wire
  5. Master cylinder solenoid (skid control ECU)
C1275/75
C1276/76
Detected only during test mode.
  1. Front speed sensor
  2. Front speed sensor rotor
  3. Master cylinder solenoid (skid control ECU)

WIRING DIAGRAM

C164934E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform zero point calibration (Click here).
  2. Check the speed sensor signal in test mode after clearing or replacement (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector of the speed sensor.Select the following menu items: Chassis / ABS/VSC/TRC/ Data List

    DATA LIST: ABS/VSC/TRC 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    FR speed sensor open detection: OPN_DET or NORMAL
    OPN_DET: Momentary interruption
    NORMAL: Normal
    -
    FL Speed Open
    FL speed sensor open detection: OPN_DET or NORMAL
    OPN_DET: Momentary interruption
    NORMAL: Normal
    -

    OK:
    There are no momentary interruptions.

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. READ VALUE USING DATA LIST (FRONT SPEED SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Select the following menu items: Chassis / ABS/VSC/TRC/ Data List

    DATA LIST: ABS/VSC/TRC 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Wheel speed sensor (FR) reading : min.: 0 km/h (0 MPH), max.: 326 km/h (202 MPH)
    Actual wheel speed
    Similar to speed indicated on speedometer
    FL Wheel Speed
    Wheel speed sensor (FL) reading : min.: 0 km/h (0 MPH), max.: 326 km/h (202 MPH)
    Actual wheel speed
    Similar to speed indicated on speedometer

  1. Check that there is no significant difference between the speed value displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    OK:
    There is almost no difference in the displayed speed values.

    HINT:
    There is a tolerance of +- 10% in the speedometer indication.



NG
Go to step 5
OK


3. PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Perform a TEST MODE inspection and check for DTCs (Click here).

    OK:
    No DTC output.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. RECONFIRM DTC
  1. Clear the DTC(s) (Click here ).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result:
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
Go to step 11
A

END

5. CHECK FRONT SPEED SENSOR INSTALLATION

  1. I044006E02
    Check that the speed sensor installation bolt is tightened properly.

    OK:
    The installation bolt is tightened properly.

Torque:
8.0 N*m{ 82 kgf*cm , 72 in.*lbf }



NG
TIGHTEN BOLT PROPERLY
OK


6. CHECK FRONT SPEED SENSOR
  1. Visually check the speed sensor for deformation and damage.

    OK:
    No scratches or foreign matter on the speed sensor tip.
    No deformation or damage.
    There is no gap between the sensor and steering knuckle.



NG
REPLACE FRONT SPEED SENSOR
OK


7. INSPECT SKID CONTROL SENSOR WIRE

  1. C135284E01
    Disconnect the skid control sensor wire.

  1. Measure the resistance.

    Standard resistance (LH):
    Tester Connection
    Specified Condition
    W1-1 - AW1-1
    Below 1 Ω
    W1-1 - AW1-2
    10 kΩ or higher
    W1-1 - Body ground
    10 kΩ or higher
    W1-2 - AW1-1
    10 kΩ or higher
    W1-2 - AW1-2
    Below 1 Ω
    W1-2 - Body ground
    10 kΩ or higher

    Standard resistance (RH):
    Tester Connection
    Specified Condition
    V1-1 - AV1-1
    Below 1 Ω
    V1-1 - AV1-2
    10 kΩ or higher
    V1-1 - Body ground
    10 kΩ or higher
    V1-2 - AV1-1
    10 kΩ or higher
    V1-2 - AV1-2
    Below 1 Ω
    V1-2 - Body ground
    10 kΩ or higher



NG
REPLACE SKID CONTROL SENSOR WIRE
OK


8. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

  1. C138455E01
    Disconnect the skid control ECU connector and the front speed sensor connector.

  1. Measure the resistance.

    Standard resistance (LH):
    Tester Connection
    Specified Condition
    A4-18 (FL+) - W1-2
    Below 1 Ω
    A4-18 (FL+) - Body ground
    10 kΩ or higher
    A4-4 (FL-) - W1-1
    Below 1 Ω
    A4-4 (FL-) - Body ground
    10 kΩ or higher

    Standard resistance (RH):
    Tester Connection
    Specified Condition
    A4-3 (FR+) - V1-2
    Below 1 Ω
    A4-3 (FR+) - Body ground
    10 kΩ or higher
    A4-17 (FR-) - V1-1
    Below 1 Ω
    A4-17 (FR-) - V1-1
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT FRONT SPEED SENSOR (INPUT VOLTAGE)

  1. C138456E01
    Disconnect the speed sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage.

    Standard voltage (LH):
    Tester Connection
    Specified Condition
    W1-2 - Body ground
    5.7 to 17.3 V

    Standard voltage (RH):
    Tester Connection
    Specified Condition
    V1-2 - Body ground
    5.7 to 17.3 V



NG
REPLACE MASTER CYLINDER SOLENOID (Click here)
OK


10. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


11. REPLACE FRONT SPEED SENSOR
  1. Replace the front speed sensor (Click here).


NEXT


12. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID (Click here)


← 43 ABS Control System Malfunction (from Aug 2012)C0210/33 Rear Speed Sensor RH Circuit (+ 7 more codes) (Jul 2007 – Oct 2010) →