2011-2016 FJ Cruiser · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Nov 2010 – Jul 2013

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. REMOVE V-BANK COVER

  1. A221454E02
    Raise the front of the V-bank cover to disengage the 2 pins.

  1. Remove the 2 V-bank cover hooks from the bracket.

  1. Remove the V-bank cover.

    Text in Illustration 
    *1
    Pin
    *2
    Hook


2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.

  1. A224743E01
    Unhook the engine under cover from the frame as shown in the illustration.
    Text in Illustration 
    *a
    Hook
    *b
    Frame


3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the service hole cover from the engine under cover.

  1. A070279E02
    Install a vinyl hose onto the drain on the radiator side.
    Text in Illustration 
    *1
    Vinyl Hose
    *2
    Tape

  1. Fix the vinyl hose with tape.

    A220213E01

    Text in Illustration 
    *1
    Radiator Cap
    *2
    Reservoir Cap
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the 2 cylinder block drain cock plugs and drain the coolant from the engine.

    NOTICE:
    If coolant is not drained from the radiator drain cock plug, cylinder block drain cock plugs and radiator reservoir, clogging in the radiator or coolant leakage from the seal of water pump may result.


4. REMOVE UPPER RADIATOR SUPPORT SEAL

  1. A226630
    Disengage the 7 clips, then remove the radiator support seal.


5. REMOVE FAN SHROUD

  1. A226631
    Disconnect the reservoir hose from the radiator.

  1. A226632
    Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the fan and V-ribbed belt (Click here).

  1. A226634
    Disengage the claw to open the hose clamp and disconnect the oil cooler tube from the fan shroud.

  1. Remove the bolt from the reserve tank.

  1. Remove the 2 bolts from the fan shroud.

  1. Disengage the claws of the shroud from the radiator as shown in the illustration.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.


6. REMOVE RADIATOR GRILLE

  1. B134729
    Using a clip remover, remove the 2 clips.

  1. Remove the 2 screws.

  1. Disengage the 5 clips and remove the radiator grille.


7. DISCONNECT NO. 1 RADIATOR HOSE

  1. A226635
    Disconnect the radiator hose.


8. DISCONNECT NO. 2 RADIATOR HOSE

  1. A226636
    Disconnect the radiator hose.


9. DISCONNECT OIL COOLER HOSE (for Automatic Transmission)

  1. A226646
    Disconnect the 2 oil cooler hoses.


10. REMOVE RADIATOR ASSEMBLY

  1. Remove the 4 bolts, then remove the radiator.

    A129886


11. REMOVE NO. 1 RADIATOR HOSE

  1. A226640
    Remove the radiator hose.


12. REMOVE NO. 2 RADIATOR HOSE

  1. A226639
    Remove the radiator hose.


13. REMOVE NO. 1 RADIATOR SUPPORT BUSH

  1. A226637
    Remove the 4 radiator supports and radiator support bushes.


14. REMOVE RADIATOR DRAIN COCK SUB-ASSEMBLY
  1. Remove the radiator drain cock plug from the radiator.

← REMOVAL (Aug 2009 – Oct 2010)REMOVAL (Aug 2013 – Jul 2014) →