2011-2016 FJ Cruiser · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. REMOVE V-BANK COVER

  1. A229925E04
    Raise the front of the V-bank cover to disengage the 2 cushions of the V-bank cover from the 2 pins.
    Text in Illustration 
    *1
    Cushion
    *2
    Pin
    *3
    Hook
    *4
    No. 1 V-bank Cover Bracket

  1. Disengage the 2 hooks to remove the V-bank cover from the No. 1 V-bank cover bracket.


2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.

  1. A224743E01
    Unhook the engine under cover from the frame as shown in the illustration.
    Text in Illustration 
    *a
    Hook
    *b
    Frame


3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the service hole cover from the engine under cover.

  1. A070279E03
    Install a vinyl hose to the radiator drain cock on the radiator assembly side.
    Text in Illustration 
    *a
    Vinyl Hose
    *b
    Tape

  1. Fix the vinyl hose with tape.

    A307922E01

    Text in Illustration 
    *1
    Radiator Cap Sub-assembly
    *2
    Radiator Reserve Tank Cap Sub-assembly
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly and drain the engine coolant.

    HINT:
    Collect the engine coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the engine coolant from the engine.

    NOTICE:
    If engine coolant is not drained from the radiator drain cock plug, cylinder block drain cock plug and radiator reservoir, clogging in the radiator assembly or engine coolant leakage from the seal of water pump may result.


4. REMOVE UPPER RADIATOR SUPPORT SEAL

  1. A226630
    Disengage the 7 clips to remove the upper radiator support seal from the fan shroud.


5. REMOVE FAN SHROUD (for Automatic Transmission)

  1. A289174
    Disconnect the radiator reserve tank hose from the radiator assembly.

  1. A226632
    Loosen the 4 nuts holding the fan and fluid coupling assembly.

  1. A217571
    While turning the V-ribbed belt tensioner assembly counterclockwise, align the service hole for the V-ribbed belt tensioner assembly and the V-ribbed belt tensioner assembly fixing position, and then insert a bar of φ 6 mm (0.236 in.) into the service hole to fix the V-ribbed belt tensioner assembly in place.

    HINT:
    The pulley bolt for the V-ribbed belt tensioner assembly has a left-hand thread.

  1. Remove the fan and generator V belt.

  1. A287966E01
    Disengage the clamp to separate the 2 oil cooler hoses from the hose clamp.
    Text in Illustration 
    *1
    Oil Cooler Hose

  1. Remove the bolt to separate the radiator reserve tank assembly from the radiator assembly.

  1. Remove the 2 bolts to separate the fan shroud from the radiator assembly.

  1. Disengage the 2 guides of the fan shroud from the radiator assembly as shown in the illustration.

  1. Remove the 4 nuts of the fan and fluid coupling assembly, and then remove the fan shroud together with the fan and fluid coupling assembly.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the engine water pump assembly.


6. REMOVE FAN SHROUD (for Manual Transmission)

  1. A289174
    Disconnect the radiator reserve tank hose from the radiator assembly.

  1. A226632
    Loosen the 4 nuts holding the fan and fluid coupling assembly.

  1. A217571
    While turning the V-ribbed belt tensioner assembly counterclockwise, align the service hole for the V-ribbed belt tensioner assembly and the V-ribbed belt tensioner assembly fixing position, and then insert a bar of φ 6 mm (0.236 in.) into the service hole to fix the V-ribbed belt tensioner assembly in place.

    HINT:
    The pulley bolt for the V-ribbed belt tensioner assembly has a left-hand thread.

  1. Remove the fan and generator V belt.

  1. A289102
    Remove the bolt to separate the radiator reserve tank assembly from the radiator assembly.

  1. Remove the 2 bolts to separate the fan shroud from the radiator assembly.

  1. Disengage the 2 guides of the fan shroud from the radiator assembly as shown in the illustration.

  1. Remove the 4 nuts of the fan and fluid coupling assembly, and then remove the fan shroud together with the fan and fluid coupling assembly.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the engine water pump assembly.


7. REMOVE RADIATOR GRILLE

  1. B134729
    Using a clip remover, remove the 2 clips.

  1. Remove the 2 screws.

  1. Disengage the 5 clips and remove the radiator grille.


8. DISCONNECT NO. 1 RADIATOR HOSE (w/ Secondary Air Injection System)

  1. A287963
    Remove the hose clamp from the No. 1 radiator hose and No. 1 air injection system hose.

  1. Slide the hose clip and disconnect the No. 1 radiator hose from the water inlet housing.


9. DISCONNECT NO. 1 RADIATOR HOSE (w/o Secondary Air Injection System)

  1. A226635
    Slide the hose clip and disconnect the No. 1 radiator hose from the water inlet housing.


10. DISCONNECT NO. 2 RADIATOR HOSE

  1. A226636
    Slide the hose clip and disconnect the No. 2 radiator hose from the water inlet with thermostat.


11. DISCONNECT OIL COOLER HOSE (for Automatic Transmission)

  1. A226646
    Slide the 2 hose clips and disconnect the 2 oil cooler hoses from the radiator assembly.


12. REMOVE RADIATOR ASSEMBLY

  1. Remove the 4 bolts and radiator assembly from the vehicle.

    A129886


13. REMOVE NO. 1 RADIATOR HOSE

  1. A226640
    Slide the hose clip and remove the No. 1 radiator hose from the radiator assembly.


14. REMOVE NO. 2 RADIATOR HOSE

  1. A226639
    Slide the hose clip and remove the No. 2 radiator hose from the radiator assembly.


15. REMOVE NO. 1 RADIATOR SUPPORT BUSH

  1. A287967E01
    Remove the 2 No. 1 radiator supports, 2 No. 2 radiator supports and 4 No. 1 radiator support bushes from the radiator assembly.
    Text in Illustration 
    *1
    No. 1 Radiator Support Bush
    *2
    No. 1 Radiator Support
    *3
    No. 2 Radiator Support


16. REMOVE RADIATOR DRAIN COCK SUB-ASSEMBLY
  1. Remove the radiator drain cock sub-assembly from the radiator assembly.

    HINT:
    Replace the O-ring if it is damaged.

← REMOVAL (Aug 2013 – Jul 2014)DISASSEMBLY (Jul 2007 – Jul 2009) →