B1642/81 Lost Communication with Driver Side Satellite Sensor Bus
Diagnostic trouble codes · Vehicles built from Aug 2008
DESCRIPTION
The side airbag sensor LH and the rear airbag sensor LH consist of parts including the diagnostic circuit and the lateral deceleration sensor.When the center airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1642/81 is set when a malfunction is detected in the side airbag sensor LH or rear airbag sensor LH circuit.
| DTC No. |
Detection Condition |
Trouble Area |
| B1642/81 |
|
|
WIRING DIAGRAM
Refer to DTC B1623/81 (Click here).INSPECTION PROCEDURE
- NOTICE:
- In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.
- Turn the ignition switch off.
- Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
- Disconnect the connector from the center airbag sensor assembly.
- Disconnect the connectors from the steering pad.
- Disconnect the connectors from the front passenger airbag assembly.
- Disconnect the connector from the front seat outer belt assembly LH.
- Disconnect the connector from the front seat outer belt assembly RH.
- Disconnect the connector from the front seat side airbag assembly LH.
- Disconnect the connector from the front seat side airbag assembly RH.
- Disconnect the connector from the curtain shield airbag assembly LH.
- Disconnect the connector from the curtain shield airbag assembly RH.
| 1. CHECK CONNECTORS (CENTER AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR LH) |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the No. 2 floor wire connectors from the center airbag sensor assembly and the side airbag sensor LH.
Check the No. 2 floor wire connectors and terminals (on the center airbag sensor assembly and the side airbag sensor LH sides) and check that the connectors are properly connected.
- Result:
Result
Proceed to
No problem.
A
Connectors or terminals incorrect.
B
Connector connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR LH) |


Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
L23-24 (BBD+) - Body ground
Ignition switch ON
Below 1 V
L23-23 (BBD-) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check for open in the circuit.
Using a service wire, connect L4-4 (BBL+) and L4-3 (BBL-) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L23-24 (BBD+) - L23-23 (BBD-)
Always
Below 1Ω
Check for short in the circuit.
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L23-24 (BBD+) - L23-23 (BBD-)
Always
1 MΩ or higher
Check for short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L23-24 (BBD+) - Body ground
Always
1 MΩ or higher
L23-23 (BBD-) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 3. CHECK CONNECTORS (SIDE AIRBAG SENSOR LH - REAR AIRBAG SENSOR LH) |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the No. 2 floor wire connectors from the side airbag sensor LH and the rear airbag sensor LH.
Check the No. 2 floor wire connectors and terminals (on the side airbag sensor LH and the rear airbag sensor LH sides) and check that the connectors are properly connected.
- Result:
Result
Proceed to
No problem.
A
Connectors or terminals incorrect.
B
Connector connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 4. CHECK NO. 2 FLOOR WIRE (SIDE AIRBAG SENSOR LH - REAR AIRBAG SENSOR LH) |


Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
L4-1 (BCL+) - Body ground
Ignition switch ON
Below 1 V
L4-2 (BCL-) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check for open in the circuit.
Using a service wire, connect L6-1 (BCL-) and L6-2 (BCL+) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L4-1 (BCL+) - L4-2 (BCL-)
Always
Below 1Ω
Check for short in the circuit.
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L4-1 (BCL+) - L4-2 (BCL-)
Always
1 MΩ or higher
Check for short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L4-1 (BCL+) - Body ground
Always
1 MΩ or higher
L4-2 (BCL-) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 5. CHECK SIDE AIRBAG SENSOR LH |
Connect the connector to the center airbag sensor assembly.
Interchange the side airbag sensor LH with the side airbag sensor RH and connect the connectors to them.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here ).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here ).
- Result:
Result
Proceed to
DTC B1642/81 is output.
A
DTC B1647/82 is output.
B
DTC B1642/81 or B1647/82 is not output.
C
- HINT:
- DTCs other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | |
| 6. CHECK REAR AIRBAG SENSOR LH |
Connect the connector to the side airbag sensor LH.
Interchange the rear airbag sensor LH with the rear airbag sensor RH and connect the connectors to them.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here ).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here ).
- Result:
Result
Proceed to
DTC B1642/81 or B1647/82 is not output.
A
DTC B1642/81 is output.
B
DTC B1647/82 is output.
C
- HINT:
- DTCs other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | ||
| ||
