B1637/82 Lost Communication with Passenger Side Rear Airbag Sensor
Diagnostic trouble codes · Vehicles built from Aug 2008
Also covers:
- B1638/82 Passenger Side Rear Airbag Sensor Initialization Incomplete
DESCRIPTION
The side airbag sensor RH and rear airbag sensor RH consist of parts including the diagnostic circuit and the lateral deceleration sensor.When center airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1637/82 and B1638/82 are set when a malfunction is detected in the side airbag sensor RH or rear airbag sensor RH circuit.
| DTC No. |
Detection Condition |
Trouble Area |
| B1637/82 B1638/82 |
|
|
WIRING DIAGRAM
Refer to DTC B1628/82 (Click here).INSPECTION PROCEDURE
- NOTICE:
- In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.
- Turn the ignition switch off.
- Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
- Disconnect the connector from the center airbag sensor assembly.
- Disconnect the connectors from the steering pad.
- Disconnect the connectors from the front passenger airbag assembly.
- Disconnect the connector from the front seat outer belt assembly LH.
- Disconnect the connector from the front seat outer belt assembly RH.
- Disconnect the connector from the front seat side airbag assembly LH.
- Disconnect the connector from the front seat side airbag assembly RH.
- Disconnect the connector from the curtain shield airbag assembly LH.
- Disconnect the connector from the curtain shield airbag assembly RH.
| 1. CHECK CONNECTORS (SIDE AIRBAG SENSOR RH - REAR AIRBAG SENSOR RH) |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the floor wire connectors from the side airbag sensor RH and the rear airbag sensor RH.
Check the floor wire connectors and terminals (on the side airbag sensor RH and the rear airbag sensor RH sides) and check that the connectors are properly connected.
- Result:
Result
Proceed to
No problem.
A
Connectors or terminals incorrect.
B
Connectors connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK SIDE AIRBAG SENSOR RH |
Connect the connector to the center airbag sensor assembly.
Interchange the side airbag sensor RH with the side airbag sensor LH and connect the connectors to them.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here ).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here ).
- Result:
Result
Proceed to
DTC B1637/82 or B1638/82 is output.
A
DTC B1632/81 or B1633/81 is output.
B
DTCs B1632/81, B1633/81, B1637/82 and B1638/82 are not output.
C
- HINT:
- DTCs other than DTC B1632/81, B1633/81, B1637/82 and B1638/82 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | |
| 3. CHECK FLOOR WIRE (SIDE AIRBAG SENSOR RH - REAR AIRBAG SENSOR RH) |


Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
K2-1 (BCR+) - Body ground
Ignition switch ON
Below 1 V
K2-2 (BCR-) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check for open in the circuit.
Using a service wire, connect K3-1 (BCR-) and K3-2 (BCR+) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
K2-1 (BCR+) - K2-2 (BCR-)
Always
Below 1Ω
Check for short in the circuit.
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
K2-1 (BCR+) - K2-2 (BCR-)
Always
1 MΩ or higher
Check for short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
K2-1 (BCR+) - Body ground
Always
1 MΩ or higher
K2-2 (BCR-) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 4. CHECK REAR AIRBAG SENSOR RH |
Connect the connector to the side airbag sensor RH.
Interchange the rear airbag sensor RH with the rear airbag sensor LH and connect the connectors to them.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here ).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here ).
- Result:
Result
Proceed to
DTCs B1632/81, B1633/81, B1637/82 and B1638/82 are not output.
A
DTC B1637/82 or B1638/82 is output.
B
DTC B1632/81 or B1633/81 is output.
C
- HINT:
- DTCs other than DTC B1632/81, B1633/81, B1637/82 and B1638/82 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | ||
| ||
