2011-2016 FJ Cruiser · Service Manual BRAKE

C1232 Acceleration Sensor Stuck Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2012

Also covers:

Versions by build date: Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012

DESCRIPTION

The skid control ECU receives signals from the yaw rate sensor and deceleration sensor via the CAN communication system.
The yaw rate sensor has a built-in deceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).
If there is trouble in the bus lines between the yaw rate sensor and deceleration sensor and the CAN communication system, DTC U0123 (yaw rate sensor communication trouble) and U0124 (deceleration sensor communication trouble) are output.
DTC Code
DTC Detection Condition
Trouble Area
C1232
At vehicle speed of 10 km/h (6 mph) or more, signal from either GL1 or GL2 does not change for 30 seconds or more.
  1. ECU-IG fuse
  2. Sensor installation
  3. Harness or connector
  4. Yaw rate and deceleration sensor
  5. CAN communication system
C1243
Following condition repeats 16 times.
  1. GL1 and GL2 do not change by more than 2LSB when vehicle decelerates from 30 km/h (19 mph) to 0 km/h (0 mph).
C1245
Following condition continues for at least 60 seconds.
  1. Difference between values calculated from deceleration sensor value and vehicle speed exceeds 0.35 G.
C1279
Detected only during test mode
  1. ECU-IG fuse
  2. Sensor installation
  3. Harness or connector
  4. Yaw rate and deceleration sensor

WIRING DIAGRAM

C185399E17

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the yaw rate and deceleration sensor, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When U0073, U0123, U0124 or U0126 are output together with C1232 or C1234, inspect and repair the trouble areas indicated by U0073, U0123, U0124 or U0126 first.


1. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if DTCs U0073, U0123, C1210 and/or C1336 are output (Click here).

    Result 
    Result
    Proceed to
    DTC U0073, U0123, C1210 and/or C1336 are not output
    A
    DTC U0073 and/or U0123 are output
    B
    DTC C1210 and/or C1336 are output
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLE SHOOTING) (Click here)

C
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


2. CHECK YAW RATE AND DECELERATION SENSOR INSTALLATION
  1. Check that the yaw rate and deceleration sensor is installed properly.

    OK:
    The sensor is tightened to the specified torque.
    The sensor is not tilted.



NG
INSTALL YAW RATE AND DECELERATION SENSOR CORRECTLY (Click here)
OK


3. INSPECT YAW RATE AND DECELERATION SENSOR (IG, GND TERMINAL)

  1. C208309E18
    Disconnect the yaw rate and deceleration sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E83-4 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E83-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Deceleration Sensor)

Result 
Result
Proceed to
OK (When troubleshooting in accordance with DTC CHART)
A
OK (When troubleshooting in accordance with PROBLEM SYMPTOMS TABLE)
B
NG
C


B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE YAW RATE AND DECELERATION SENSOR (Click here)


← C1232 Acceleration Sensor Stuck Malfunction (+ C1243, C1245, C1279) (Aug 2011 – Jul 2012)C1240 Yaw Rate Sensor Discrimination (Nov 2010 – Jul 2012) →