C1232 Acceleration Sensor Stuck Malfunction
Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2011
Also covers:
- C1243 Acceleration Sensor Stuck Malfunction
- C1245 Acceleration Sensor Output Malfunction
- C1279 Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)
Versions by build date: Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012
DESCRIPTION
The skid control ECU receives signals from the yaw rate sensor and deceleration sensor via the CAN communication system.The yaw rate sensor has a built-in deceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).
If there is trouble in the bus lines between the yaw rate sensor and deceleration sensor and the CAN communication system, DTC U0123 (yaw rate sensor communication trouble) and U0124 (deceleration sensor communication trouble) are output.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1232 |
At vehicle speed of 10 km/h (6 mph) or more, signal from either GL1 or GL2 does not change for 30 seconds or more. |
|
| C1243 |
Following condition repeats 16 times.
|
|
| C1245 |
Following condition continues for at least 60 seconds.
|
|
| C1279 |
Detected only during test mode |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the yaw rate and deceleration sensor, perform zero point calibration (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When replacing the yaw rate and deceleration sensor, perform zero point calibration (Click here).
- HINT:
- When U0073, U0123, U0124 or U0126 are output together with C1232 or C1234, inspect and repair the trouble areas indicated by U0073, U0123, U0124 or U0126 first.
| 1. CHECK DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Check if DTCs U0073, U0123, C1210 and/or C1336 are output (Click here).
Result Result
Proceed to
DTC U0073, U0123, C1210 and/or C1336 are not output
A
DTC U0073 and/or U0123 are output
B
DTC C1210 and/or C1336 are output
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK YAW RATE AND DECELERATION SENSOR INSTALLATION |
Check that the yaw rate and deceleration sensor is installed properly.
- OK:
- The sensor is tightened to the specified torque.
The sensor is not tilted.
|
|
||||
| OK | |
| 3. INSPECT YAW RATE AND DECELERATION SENSOR (IG, GND TERMINAL) |
Disconnect the yaw rate and deceleration sensor connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E83-4 (IG) - Body ground
Ignition switch ON
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E83-1 (GND) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Yaw Rate and Deceleration Sensor)
| Result |
Proceed to |
| OK (When troubleshooting in accordance with DTC CHART) |
A |
| OK (When troubleshooting in accordance with PROBLEM SYMPTOMS TABLE) |
B |
| NG |
C |
|
|
||||
|
|
||||
| A | ||
| ||
