2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

Check CAN Bus Lines for Short Circuit (RHD Models)

Circuit diagnosis · Vehicles built Aug 2011 – Jul 2012

Versions by build date: Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012

DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
  1. Short between CAN bus lines
  2. ECM
  3. Combination meter assembly (combination meter ECU)
  4. Yaw rate sensor
  5. Master cylinder solenoid (skid control ECU)
  6. Steering angle sensor
  7. Airbag sensor assembly
  8. CAN junction connector No. 1
  9. CAN junction connector No. 2
  10. CAN junction connector No. 3

WIRING DIAGRAM

E231209E02

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the ignition switch off before inspecting CAN bus wires for a ground short.
  3. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE)

  1. E194173E22
    Disconnect the E91 CAN junction connector No. 2 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-14 (CANL)
    Ignition switch off
    1 MΩ or higher

Text in Illustration 
*a
Front view of DLC3


NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


3. CONNECT CONNECTOR
  1. Reconnect the E91 CAN junction connector No. 2 connector.


NEXT


4. CHECK FOR SHORT IN CAN BUS WIRES (JUNCTION CONNECTOR NO. 3 SIDE)

  1. E194173E22
    Disconnect the A43 CAN junction connector No. 3 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-14 (CANL)
    Ignition switch off
    108 to 132 Ω

Text in Illustration 
*a
Front view of DLC3


NG
Go to step 7
OK


5. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR NO. 3 - COMBINATION METER ASSEMBLY (COMBINATION METER ECU))

  1. E214897E10
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-2 (CANH) - A43-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 3)



NG
Go to step 16
OK


6. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR NO. 3 - MASTER CYLINDER SOLENOID (SKID CONTROL ECU))

  1. E214897E12
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-1 (CANH) - A43-12 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 3)



NG
Go to step 18
OK

REPLACE CAN JUNCTION CONNECTOR NO. 3

7. CONNECT CONNECTOR
  1. Reconnect the A43 CAN junction connector No. 3 connector.


NEXT


8. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR NO. 3 - CAN JUNCTION CONNECTOR NO. 2)
  1. Disconnect the E92 CAN junction connector No. 2 connector.

  1. E218523E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-3 (CANH) - A43-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (CAN Junction Connector No. 3)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK


9. CONNECT CONNECTOR
  1. Reconnect the E92 CAN junction connector No. 2 connector.


NEXT


10. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR NO. 1 SIDE)

  1. E194173E22
    Disconnect the E95 CAN junction connector No. 1 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-14 (CANL)
    Ignition switch off
    108 to 132 Ω

Text in Illustration 
*a
DLC3


NG
Go to step 15
OK


11. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR NO. 2 - CAN JUNCTION CONNECTOR NO. 1)

  1. E214897E08
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-3 (CANH) - E95-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK


12. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR NO. 1 - ECM)

  1. E214897E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-1 (CANH) - E95-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)



NG
Go to step 20
OK


13. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR NO. 1 - YAW RATE SENSOR)

  1. E214897E09
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-2 (CANH) - E95-13 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)



NG
Go to step 22
OK


14. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR NO. 1 - AIRBAG SENSOR ASSEMBLY)

  1. E214897E14
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-7 (CANH) - E95-18 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)



NG
Go to step 24
OK

REPLACE CAN JUNCTION CONNECTOR NO. 1

15. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR NO. 2 - STEERING ANGLE SENSOR)

  1. E214898E05
    Disconnect the E91 CAN junction connector No. 2 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E91-5 (CANH) - E91-11 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 2)



NG
Go to step 27
OK

REPLACE CAN JUNCTION CONNECTOR NO. 2

16. CONNECT CONNECTOR
  1. Reconnect the A43 CAN junction connector No. 3 connector.


NEXT


17. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY (COMBINATION METER ECU))

  1. E214880E01
    Disconnect the E14 combination meter assembly (combination meter ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E14-10 (CANH) - E14-9 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly (Combination Meter ECU))



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE COMBINATION METER ASSEMBLY (COMBINATION METER ECU) (Click here)

18. CONNECT CONNECTOR
  1. Reconnect the A43 CAN junction connector No. 3 connector.


NEXT


19. CHECK FOR SHORT IN CAN BUS WIRES (MASTER CYLINDER SOLENOID (SKID CONTROL ECU))

  1. B255884E02
    Disconnect the A4 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-11 (CANH) - A4-25 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid (Skid Control ECU))



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)

20. CONNECT CONNECTOR
  1. Reconnect the E95 CAN junction connector No. 1 connector.


NEXT


21. CHECK FOR SHORT IN CAN BUS WIRES (ECM)

  1. E214877E02
    Disconnect the E81 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E81-32 (CANH) - E81-31 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE ECM (Click here)

22. CONNECT CONNECTOR
  1. Reconnect the E95 CAN junction connector No. 1 connector.


NEXT


23. CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR)

  1. E175983E04
    Disconnect the E83 yaw rate sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E83-3 (CANH) - E83-2 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE YAW RATE SENSOR (Click here)

24. CONNECT CONNECTOR
  1. Reconnect the E95 CAN junction connector No. 1 connector.


NEXT


25. CHECK FOR SHORT IN CAN BUS WIRES (AIRBAG SENSOR ASSEMBLY)

  1. E186790E14
    Disconnect the E29 airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E29-13 (CANH) - E29-22 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE AIR BAG SENSOR ASSEMBLY (Click here)

26. CONNECT CONNECTOR
  1. Reconnect the E91 CAN junction connector No. 2 connector.


NEXT


Go to step 25

27. CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)

  1. E192049E04
    Disconnect the E16 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-3 (CANH) - E16-11 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE STEERING ANGLE SENSOR (Click here)


← Check CAN Bus Lines for Short Circuit (RHD Models) (Nov 2010 – Jul 2011)Check CAN Bus Lines for Short Circuit (RHD Models) (from Aug 2012) →