2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

Check CAN Bus Line for Short to +B (LHD Models)

Circuit diagnosis · Vehicles built Nov 2010 – Jul 2011

Versions by build date: Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012

DESCRIPTION

There may be a short circuit between the CAN bus line and +B when there is resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.
Symptom
Trouble Area
There is resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.
  1. Short to +B
  2. ECM
  3. Combination meter assembly (combination meter ECU)
  4. Yaw rate sensor
  5. Master cylinder solenoid (skid control ECU)
  6. Steering angle sensor
  7. CAN junction connector No. 1

WIRING DIAGRAM

E218496E03

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the ignition switch off before inspecting CAN bus wires for a ground short.
  3. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 BRANCH WIRE)

  1. E194173E23
    Disconnect the E95 CAN junction connector No. 1 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E1-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


3. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR NO. 1 - YAW RATE SENSOR)

  1. E214902E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-2 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E95-13 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)
    *b
    DLC3



NG
Go to step 8
OK


4. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR NO. 1 - STEERING ANGLE SENSOR)

  1. E214902E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-5 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E95-16 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)
    *b
    DLC3



NG
Go to step 9
OK


5. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR NO. 1 - MASTER CYLINDER SOLENOID (SKID CONTROL ECU))

  1. E214902E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E95-17 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)
    *b
    DLC3



NG
Go to step 10
OK


6. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR NO. 1 - ECM)

  1. E214902E05
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-1 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E95-12 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)
    *b
    DLC3



NG
Go to step 11
OK


7. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR NO. 1 - COMBINATION METER ASSEMBLY (COMBINATION METER ECU))

  1. E214902E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-3 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E95-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)
    *b
    DLC3



NG
Go to step 12
OK

REPLACE CAN JUNCTION CONNECTOR NO. 1

8. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR)

  1. E214902E02
    Disconnect the E83 yaw rate sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-2 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E95-13 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE YAW RATE SENSOR (Click here)

9. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR)

  1. E214902E03
    Disconnect the E16 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-5 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E95-16 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE STEERING ANGLE SENSOR (Click here)

10. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MASTER CYLINDER SOLENOID (SKID CONTROL ECU))
  1. Disconnect the A4 master cylinder solenoid (skid control ECU) connector.

  1. E214902E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E95-17 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)

11. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM MAIN WIRE)
  1. Disconnect the E81 ECM connector.

  1. E214902E05
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-1 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E95-12 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE ECM (Click here)

12. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY (COMBINATION METER ECU))
  1. Disconnect the E14 combination meter assembly (combination meter ECU) connector.

  1. E214902E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-3 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E95-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE COMBINATION METER ASSEMBLY (COMBINATION METER ECU) (Click here)


← Check CAN Bus Line for Short to GND (Aug 2009 – Oct 2010)Check CAN Bus Line for Short to +B (LHD Models) (Aug 2011 – Jul 2012) →