2011-2016 FJ Cruiser · Service Manual ENGINE

Fuel Pump Control Circuit

Circuit diagnosis · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2012 Aug 2012 – Oct 2012 Nov 2012 – Jul 2014 from Aug 2014

DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump and fuel pump control ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump control ECU adjusts the fuel pump operation speed between 3 settings.

WIRING DIAGRAM

A226165E04

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL PUMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check whether operating sounds can be heard while operating the fuel pump using the tester.

    OK:
    Operating sounds can be heard from fuel pump.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT CIRCUIT OPENING RELAY (C/OPN)
B016200E02
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE CIRCUIT OPENING RELAY (C/OPN)
OK


3. INSPECT CIRCUIT OPENING RELAY (POWER SOURCE VOLTAGE)
A219243E02
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C/OPN relay terminal 1- Body ground
    Ignition switch ON
    11 to 14 V
    C/OPN relay terminal 5 - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*1
Engine Room Relay Block


NG
Go to step 10
OK


4. CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - ECU, FUEL PUMP CONTROL ECU)
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Disconnect the fuel pump control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay terminal 2 - E81-8 (FC)
    Always
    Below 1 Ω
    C/OPN relay terminal 3 - O1-4 (+B)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay terminal 2 or E81-8 (FC) - Body ground
    Always
    10 kΩ or higher
    C/OPN relay terminal 3 or O1-4 (+B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP CONTROL ECU)
  1. Disconnect the fuel pump connector.

  1. Disconnect the fuel pump control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    L5-4 - O2-1 (FP)
    Always
    Below 1 Ω
    L5-5 - O2-2 (FP-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    L5-4 or O2-1 (FP) - Body ground
    Always
    10 kΩ or higher
    L5-5 or O2-2 (FP-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - ECM, BODY GROUND)
  1. Disconnect the fuel pump control ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    O1-1 (FPC) - E82-3 (FPC)
    Always
    Below 1 Ω
    O1-2 (DI) - E81-26 (DI)
    Always
    Below 1 Ω
    O1-3 (E) - Body ground
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    O1-1 (FPC) or E82-3 (FPC) - Body ground
    Always
    10 kΩ or higher
    O1-2 (DI) or E81-26 (DI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. REPLACE FUEL PUMP CONTROL ECU
  1. Replace the fuel pump control ECU (Click here).


NEXT


9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check the fuel pump operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END

10. CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - EFI RELAY, IGNITION SWITCH)
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Remove the EFI relay (EFI) from the engine room relay block.

  1. Disconnect the ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay terminal 5 - EFI relay terminal 3
    Always
    Below 1 Ω
    C/OPN relay terminal 1 - A1-6 (IG2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C/OPN relay terminal 5 or EFI relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    C/OPN relay terminal 1 or A1-6 (IG2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)


← Fuel Pump Control Circuit (Dec 2007 – Jul 2009)Fuel Pump Control Circuit (Nov 2010 – Jul 2012) →