Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0016    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

DTC    P0017    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)

DTC    P0018    Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)

DTC    P0019    Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)

for Preparation Click here


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake and exhaust valve open and close timing is controlled by the ECM. The ECM performs intake and exhaust valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve assembly, and operating the camshaft timing gear assembly; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No.
DTC Detection Condition
Trouble Area
P0016
Deviation in the crankshaft position sensor signal and VVT sensor (for Intake side of bank 1) signal (2 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for intake side of bank 1)
  3. Oil control valve filter
  4. Camshaft timing gear assembly (for bank 1)
  5. ECM
P0017
Deviation in the crankshaft position sensor signal and VVT sensor (for Exhaust side of bank 1) signal (2 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for exhaust side of bank 1)
  3. Oil control valve filter
  4. Camshaft timing exhaust gear assembly (for bank 1)
  5. ECM
P0018
Deviation in the crankshaft position sensor signal and VVT sensor (for Intake side of bank 2) signal (2 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for intake side of bank 2)
  3. Oil control valve filter
  4. Camshaft timing gear assembly (for bank 2)
  5. ECM
P0019
Deviation in the crankshaft position sensor signal and VVT sensor (for Exhaust side of bank 2) signal (2 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for exhaust side of bank 2)
  3. Oil control valve filter
  4. Camshaft timing exhaust gear assembly (for bank 2)
  5. ECM

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0016 (Bank 1) or P0018 (Bank 2).
To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0017 (Bank 1) or P0019 (Bank 2).

MONITOR STRATEGY


Related DTCs
P0016: Camshaft timing misalignment at idling (Intake Side Bank 1)
P0017: Camshaft timing misalignment at idling (Exhaust Side Bank 1)
P0018: Camshaft timing misalignment at idling (Intake Side Bank 2)
P0019: Camshaft timing misalignment at idling (Exhaust Side Bank 2)
Required Sensors/Components (Main)
Camshaft timing gear
Required Sensors/Components (Related)
VVT sensor, Crankshaft position sensor
Frequency of Operation
Continuous
Duration
Within 1 minute
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P0016 and P0018 
Monitor runs whenever following DTCs not present
P0010, P0020 (VVT oil control valve)
P0016, P0018 (VVT system - misalignment)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
Engine speed
500 to 1000 rpm

P0017 and P0019 
Monitor runs whenever following DTCs not present
P0013, P0023 (Exhaust VVT oil control valve)
P0017, P0019 (Exhaust VVT system - misalignment)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
Engine speed
500 to 1000 rpm

TYPICAL MALFUNCTION THRESHOLDS


Intake side: 
One of following conditions met
-
VVT learning value at maximum retarded valve timing
Less than 25.1° CA
VVT learning value at maximum retarded valve timing
More than 49.9° CA

Exhaust side: 
One of following conditions met
-
VVT learning value at maximum advanced valve timing
Less than 81.1° CA
VVT learning value at maximum advanced valve timing
More than 105.9° CA

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN


A197314E13

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  7. Idle the engine for 5 minutes or more [C].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0016, P0017, P0018 or P0019.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].

  13. Drive the vehicle for 2 to 3 minutes [E].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Idle the engine for 5 minutes or more [F].
  15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [G].
  16. Read pending DTCs [G].

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Check the DTC judgment result.
  18. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
  1. The monitor for this DTC detects when the timing chain is shifted by one tooth or more.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016, P0017, P0018 OR P0019)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0016, P0017, P0018 or P0019 is output
    A
    P0016, P0017, P0018 or P0019 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0016, P0017, P0018 or P0019 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)

HINT:
If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.

  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2) or Control the VVT Exhaust Linear (Bank 1) or Control the Exhaust VVT Linear (Bank 2) / VVT Change Angle #1, VVT Change Angle #2, VVT Ex Chg Angle #1, VVT Ex Chg Angle #2.

  1. Perform the Active Test. Check that the displacement angle varies.

    OK:
    Displacement angle varies.



NG
Go to step 4
OK


3.ADJUST VALVE TIMING
  1. Adjust the valve timing (Click here).



NEXT
Go to step 7

4.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST SIDE)
  1. Inspect the camshaft timing oil control valve assembly (for intake or exhaust side) (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST SIDE) (Click here)
OK


5.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT EXHAUST TIMING GEAR ASSEMBLY
  1. Inspect camshaft timing gear assembly or camshaft timing exhaust gear assembly .

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing gear assembly or camshaft timing exhaust gear assembly (Click here).



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT EXHAUST TIMING GEAR ASSEMBLY (Click here)
OK


6.INSPECT OIL CONTROL VALVE FILTER
  1. Remove the oil control valve filter (Click here).

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.



NG
CLEAN OR REPLACE OIL CONTROL VALVE FILTER
OK


7.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read the output pending DTCs using the Techstream.

OK:
No pending DTC is output.



NG
REPLACE ECM (Click here)
OK

END