Home › ENGINE › 1GR-FE IGNITION › IGNITION SYSTEM

IGNITION SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. PERFORM SPARK TEST
  1. Check for DTCs (Click here).

    NOTICE:
    If any DTC is output, perform troubleshooting procedures for that DTC.



  1. Check if sparks occur.

    1. Remove the intake air surge tank (Click here).

    2. Remove the 6 spark plugs (Click here).



    3. A227073
    4. Disconnect the 6 injector connectors.

    5. Install the spark plug to each ignition coil assemblies and connect the ignition coil assembly connectors.

    6. Ground the spark plugs.

    7. Check that sparks occur while the engine is being cranked.

      NOTICE:
      1. Ground the spark plugs when checking them.
      2. Replace any ignition coils that have been subjected to a physical impact.
      3. Do not crank the engine for more than 2 seconds.

      If sparks do not occur, perform the following procedure.

  1. Perform the spark test in accordance with the following procedure.

    1. Check that the wire harness side connector of the ignition coil is securely connected.
      Result 
      Result
      Proceed to
      NG
      Connect securely
      OK
      Go to next step

  1. Perform a spark test on each ignition coil.

    1. If there is a cylinder where sparks do not occur, replace its ignition coil with the ignition coil of a cylinder where sparks occur normally.

    2. Crank the engine and visually check that sparks occur at the cylinder with the normally operating ignition coil.
      Result 
      Result
      Proceed to
      OK
      Replace ignition coil
      NG
      Go to next step

  1. Inspect the spark plug.

    1. Replace the spark plug with a normal one.

    2. Perform spark test again.
      Result 
      Result
      Proceed to
      OK
      Replace spark plug
      NG
      Go to next step






    1. A207834E02
    2. Check that power is supplied to the ignition coil.
      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Ignition Coil)

      1. Turn the ignition switch to ON.
      2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      1 (+B) - 4 (GND)
      Ignition switch ON
      11 to 14 V

      Result 
      Result
      Proceed to
      NG
      Check wiring between ignition switch and ignition coil and check ground circuit
      OK
      Replace the ECM (Click here)

  1. Connect the 6 injector connectors.

  1. Install the 6 spark plugs .

  1. Install the intake air surge tank (Click here).

  1. Clear the DTC (Click here).

  1. Check for DTCs (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.



2. INSPECT SPARK PLUG

NOTICE:
  1. Do not use a wire brush for cleaning.
  2. Do not attempt to adjust the electrode gap of a used spark plug.



    I039522E32
  1. Check the electrode.
    Text in Illustration 
    *a
    Ground

    1. Using a megohmmeter, measure the insulation resistance.

      Standard Insulation Resistance:
      Tester Connection
      Condition
      Specified Condition
      Spark Plug (terminal part) - Ground
      Always
      10 MΩ or higher

      HINT:
      1. If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.
      2. If a megohmmeter is not available, perform the following simple inspection instead.



  1. Alternative inspection method:

    1. Start the engine.

    2. Quickly accelerate the engine to 4000 rpm 5 times.

    3. Remove the 6 spark plugs.



    4. A126881
    5. Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage on its threads and insulator.
    If there is any damage, replace the spark plug.

    Recommended Spark Plug:
    Manufacturer
    Product
    DENSO made
    SK16HR11



  1. Reference:



      A227070E01
    1. Check the spark plug electrode gap.
      Text in Illustration 
      *a
      Spark Plug Electrode Gap

      Maximum electrode gap for used spark plug:
      1.3 mm (0.0512 in.)

      If the gap is more than the maximum, replace the spark plug.

      Electrode gap for new spark plug:
      1.0 to 1.1 mm (0.0394 to 0.0433 in.)

      NOTICE:
      Never attempt to adjust the electrode gap of a used spark plug.



    B062019E01
  1. Clean the spark plugs.
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Standard air pressure:
    588 kPa (6 kgf/cm2, 85 psi)

    Standard duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.