Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0335    Crankshaft Position Sensor "A" Circuit

DTC    P0339    Crankshaft Position Sensor "A" Circuit Intermittent

for Preparation Click here


DESCRIPTION

The crankshaft position sensor system consists of a crank angle sensor plate and a pickup coil. The crank angle sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and a magnet.
The crank angle sensor plate rotates and, as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No.
DTC Detection Condition
Trouble Area
P0335
One of the following conditions is met when VVT sensor circuit fail is not detected (1 trip detection logic):
  1. No crankshaft position sensor signal to ECM while cranking
  2. No crankshaft position sensor signal to ECM while engine running
  3. Missing crankshaft position sensor signal despite VVT sensor signal inputs normal after engine cranked
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft (crank angle sensor plate)
  4. ECM
P0339
Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more
(1 trip detection logic):
(a) Engine speed 1000 rpm or more
(b) Starter signal off
(c) 3 seconds or more have elapsed since starter signal switched from ON to OFF

VV1, VV2 and NE signal waveforms
  1. A122767E13
  2. Inspection using an oscilloscope.

    HINT:
    1. The correct waveform is shown above.
    2. VV1+ and VV2+ stand for the VVT sensor (for intake side) signal, and NE+ stands for the crankshaft position sensor signal.
      Item
      Content
      Terminal
      VV1+ - VV1-
      VV2+ - VV2-
      NE+ - NE-
      Equipment Setting
      5 V/DIV
      20 ms/DIV
      Condition
      Idling


MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the engine revolving, the ECM interprets this as a malfunction of the sensor.
If the malfunction is not repaired successfully, a DTC is stored 20 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0335: Crankshaft position sensor range check/rationality
P0335: Crankshaft position sensor verify pulse input
Required Sensors/Components (Main)
Crankshaft position sensor
Required Sensors/Components (Related)
VVT sensor
Frequency of Operation
Continuous
Duration
-: Verify pulse input case 1
4.7 seconds: Verify pulse input case 2
0.016 seconds: Range check/rationality
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not present
None

Crankshaft Position Sensor Range Check/Rationality 
Crankshaft position sensor signal
Signal input
Ignition switch
ON
Time after starter off to ON
3 seconds or more
Number of VVT sensor signal pulses
6 times
Battery voltage
7 V or more
Minimum battery voltage while starter ON
Less than 11 V
VVT sensor circuit (P0340, P0342, P0343)
Not detected

Crankshaft Position Sensor Verify Pulse Input: Case 1 
Starter
OFF
Engine speed (Top dead center)
600 rpm or more
Engine speed (30°CA)
600 rpm or more
Time after starter ON to OFF
3 seconds or more

Crankshaft Position Sensor Verify Pulse Input: Case 2 
Starter
ON
Minimum battery voltage while starter ON
Less than 11 V

TYPICAL MALFUNCTION THRESHOLDS


Crankshaft Position Sensor Range Check/Rationality 
Number of crankshaft position sensor signal pulses
132 or less, and 174 or more

Crankshaft Position Sensor Verify Pulse Input: Case 1 and 2 
Crankshaft position sensor signal
No signal

COMPONENT OPERATING RANGE


Crankshaft position sensor
  1. Crankshaft position sensor output voltage fluctuates while crankshaft revolving
  2. 34 crankshaft position sensor signals per crankshaft revolution

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 20 seconds or more [A].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  9. Read DTCs.

    HINT:
    1. If a DTC is output, the system is malfunctioning.
    2. If a DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0335 or P0339.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

  13. If no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A241852E02


INSPECTION PROCEDURE

HINT:
  1. After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the VVT sensor.
    1. Installation condition of the VVT sensor.
    2. Installation condition of the camshaft.
    3. Connection of the VVT sensor connector.
  2. If no problem is found by this diagnostic troubleshooting procedure, troubleshoot the engine mechanical systems.
  3. Check the engine speed. The engine speed can be checked by using a Techstream. To check, follow the operation below:
    1. Connect the Techstream to the DLC3.
    2. Start the engine.
    3. Turn the Techstream on.
    4. Enter the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
    1. The engine speed may be indicated as zero despite the engine revolving normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed, if the CKP sensor voltage output is insufficient.
  4. Read freeze frame data using the Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
  1. Inspect the crankshaft position sensor (Click here).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B29-1 - B47-6 (NE+)
    Always
    Below 1 Ω
    B29-2 - B47-5 (NE-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B29-1 or B47-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    B29-2 or B47-5 (NE-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
BR03795E32
  1. Check the crankshaft position sensor installation.

    OK:
    Crankshaft position sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


4.INSPECT CRANKSHAFT (TEETH OF CRANK ANGLE SENSOR PLATE)
  1. Check the teeth of the crank angle sensor plate.

    OK:
    Crank angle sensor plate does not have any cracks or deformation.



NG
REPLACE CRANKSHAFT (Click here)
OK

REPLACE ECM (Click here)