Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2195    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)

DTC    P2196    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)

DTC    P2197    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1)

DTC    P2198    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

HINT:
Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.

The A/F sensor generates a voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio level, and regulates the fuel injection time. If the A/F sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.
The A/F sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte though the alumina, and therefore the sensor activation is accelerated.
In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.
*: Value changes inside the ECM. Since the A/F sensor is the current output element, a current is converted into a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.

A234900E23


DTC No.
DTC Detection Condition
Trouble Area
P2195
P2197
Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic)
  1. (a) Air-Fuel Ratio (A/F) sensor voltage more than 3.8 V
  2. (b) Heated Oxygen (HO2) sensor voltage 0.21 V or more
  1. Open or short in A/F sensor (for bank 1, 2 sensor 1) circuit
  2. A/F sensor (for bank 1, 2 sensor 1)
  3. A/F sensor heater (for bank 1, 2 sensor 1)
  4. A/F sensor heater relay
  5. A/F sensor heater and relay circuits
  6. Intake system
  7. Fuel pressure
  8. Fuel injector assembly
  9. ECM
While fuel-cut operation performed (during vehicle deceleration), air-fuel ratio (A/F) sensor current 2.2 mA or more for 3 seconds (2 trip detection logic)
  1. A/F sensor (for bank 1, 2 sensor 1)
  2. ECM
P2196
P2198
Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic)
  1. (a) A/F sensor voltage less than 2.8 V
  2. (b) HO2 sensor voltage is below 0.66 V
  1. Open or short in A/F sensor (for bank 1, 2 sensor 1) circuit
  2. A/F sensor (for bank 1, 2 sensor 1)
  3. A/F sensor heater (for bank 1, 2 sensor 1)
  4. A/F sensor heater relay
  5. A/F sensor heater and relay circuits
  6. Intake system
  7. Fuel pressure
  8. Fuel injector assembly
  9. ECM
While fuel-cut operation performed (during vehicle deceleration), air-fuel ratio (A/F) sensor current less than 0.7 mA for 3 seconds (2 trip detection logic)
  1. A/F sensor heater (for bank 1, 2 sensor 1)
  2. ECM

HINT:
  1. DTCs P2195 and P2196 indicate malfunctions related to bank 1 A/F sensor circuit.
  2. DTCs P2197 and P2198 indicate malfunctions related to bank 2 A/F sensor circuit.
  3. When any of these DTCs are stored, check the A/F sensor voltage output by entering the following menus: Powertrain / Engine and ECT / Data List / AFS Voltage B1S1 or AFS Voltage B2S1.
  4. Short-term fuel trim values can also be read using the Techstream.
  5. The ECM regulates the voltages at the A1A+, A2A+, A1A- and A2A- terminals of the ECM to a constant level. Therefore, the A/F sensor voltage output cannot be confirmed without using the Techstream.
  6. If a A/F sensor malfunction is detected, the ECM stores a DTC.


MONITOR DESCRIPTION

  1. Sensor voltage detection monitor
    Under the air-fuel ratio feedback control, if the A/F sensor output voltage indicates rich or lean for a certain period of time, the ECM determines that there is a malfunction in the A/F sensor. The ECM illuminates the MIL and stores DTC(s).
    Example:
    If the A/F sensor output voltage is less than 2.8 V (very rich condition) for 5 seconds, despite the rear HO2 sensor output voltage being below 0.66 V, the ECM stores DTC P2196 or P2198. Alternatively, if the A/F sensor output voltage is more than 3.8 V (very lean condition) for 5 seconds despite the rear HO2 sensor output voltage being 0.21 V or more, DTC P2195 or P2197 is stored.
  1. Sensor current detection monitor
    A rich air-fuel mixture causes a low A/F sensor current, and a lean air-fuel mixture causes a high A/F sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the A/F sensor current during fuel cut and detects any abnormal current values.
    If the A/F sensor output is 2.2 mA or more for 3 seconds or more of cumulative time, the ECM interprets this as a malfunction in the A/F sensor and stores DTC P2195 or P2197 (high-side stuck). If the A/F sensor output is less than 0.7 mA for 3 seconds or more of cumulative time, the ECM stores DTC P2196 or P2198 (low-side stuck).

A107165E47


MONITOR STRATEGY


Related DTCs
P2195: Air fuel ratio sensor (for bank 1 sensor 1) signal stuck lean
P2196: Air fuel ratio sensor (for bank 1 sensor 1) signal stuck rich
P2197: Air fuel ratio sensor (for bank 2 sensor 1) signal stuck lean
P2198: Air fuel ratio sensor (for bank 2 sensor 1) signal stuck rich
Required Sensors/Components (Main)
Air fuel ratio sensor
Required Sensors/Components (Related)
Heated oxygen sensor
Frequency of Operation
Continuous: Sensor voltage detection monitor
Once per driving cycle: Sensor current detection monitor
Duration
5 seconds: Sensor voltage detection monitor
3 seconds: Sensor current detection monitor
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT system - misalignment)
P0017, P0019 (Exhaust VVT system - misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120 - P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient engine coolant temperature for closed loop fuel control)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0306 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0412, P0418, P1613 (Secondary air injection system control)
P0416, P0417, P2440 - P2445 (Secondary air injection system)
P0451 - P0453 (EVAP system)
P0500, P0722 (Vehicle speed sensor)
P0505 (IAC valve)
P219A, P219B (Air-fuel ratio imbalance)

Sensor Voltage Detection Monitor 
Time after engine start
30 seconds or more
A/F sensor status
Activated
Fuel system status
Closed loop

Sensor Current Detection Monitor: 
Battery voltage
11 V or more
ECT
75°C (167°F) or more
Atmospheric pressure
76 kPa(abs) [570 mmHg(abs)] or more
A/F sensor status
Activated
Continuous time of fuel cut
3 to 10 seconds

TYPICAL MALFUNCTION THRESHOLDS


Sensor Voltage Detection Monitor (Lean Side Malfunction P2195 and P2197) 
Rear HO2S voltage
0.21 V or more
A/F sensor voltage
More than 3.8 V

Sensor Voltage Detection Monitor (Rich Side Malfunction P2196 and P2198) 
Rear HO2S voltage
Less than 0.66 V
A/F sensor voltage
Less than 2.8 V

Sensor Current Detection Monitor (High Side Malfunction P2195 and P2197) 
A/F sensor current
2.2 mA or more

Sensor Current Detection Monitor (Low Side Malfunction P2196 and P2198) 
A/F sensor current
Less than 0.7 mA

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN


A199318E58


A242910E03

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on.
  7. Start the engine, and warm it up until the ECT reaches 75°C (167°F) or higher [A].
  8. On the Techstream, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / Idle Fuel Cut.
  9. Drive the vehicle at between 60 km/h (37 mph) and 120 km/h (75 mph) for at least 10 minutes [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  10. Shift the transmission to 2nd gear [C].
  11. Accelerate the vehicle to 64 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  12. Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

    HINT:
    Fuel-cut is performed when the following conditions are met:
    1. Accelerator pedal is fully released.
    2. Engine speed is 2500 rpm or more (fuel injection returns at 1000 rpm).

  13. Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).
  14. Repeat steps [C] through [E] above at least 3 times in one driving cycle.
  15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].
  16. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  18. Input the DTC: P2195, P2196, P2197 or P2198.
  19. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F].

  20. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A226179E05


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
  4. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  5. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  6. Sensor 1 refers to the sensor closest to the engine assembly.
  7. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P2195, P2196, P2197 or P2198 is output
    A
    "P2195, P2196, P2197 or P2198" and "P0136, P0137, P0138, P0156, P0157 or P0158" are output
    P2195, P2196, P2197 or P2198 and other DTCs are output
    B

    HINT:
    If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST
  1. Has the vehicle run out of fuel in the past?



NO
Go to step 4
YES


3.PERFORM CONFIRMATION DRIVING PATTERN
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2195, P2196, P2197 or P2198.

  1. Check the DTC judgment.
    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P2195, P2196, P2197 or P2198 are output)
    B



B
Go to step 4
A

DTC CAUSED BY RUNNING OUT OF FUEL 

4.READ VALUE USING TECHSTREAM (TEST VALUE OF A/F SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.

  1. Check that the status of O2 Sensor is Complete.
    If the status is still Incomplete, drive the vehicle according to the driving pattern again.

  1. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Details / RANGE B1S1 or RANGE B2S1.

  1. Check the test value of the A/F sensor output current during fuel-cut.
    Result 
    Result
    Proceed to
    Within normal range (0.7 mA or more, and less than 2.2 mA)
    A
    Outside normal range (Less than 0.7 mA, or 2.2 mA or more)
    B



B
Go to step 14
A


5.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

  1. Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the 12.5 or -12.5 button to change the fuel injection volume).

  1. Monitor the voltage outputs of the A/F and HO2 sensors (AFS Voltage B1S1 or B2S1 and O2S B1S2 or B2S2) displayed on the Techstream.

    HINT:
    1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
    2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    3. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Standard Voltage:

    Techstream Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1
    AFS Voltage B2S1
    (Air fuel ratio sensor)
    12.5%
    Rich
    Less than 3.1 V
    -12.5%
    Lean
    More than 3.4 V
    O2S B1S2
    O2S B2S2
    (Heated oxygen sensor)
    12.5%
    Rich
    More than 0.55 V
    -12.5%
    Lean
    Less than 0.4 V


    Result 
    Status AFS Voltage B1S1 or AFS Voltage B2S1
    Status O2S B1S2 or O2S B2S2
    A/F Condition and A/F Sensor Condition
    Proceed to
    Lean
    Lean
    Actual air fuel ratio lean
    A
    Rich
    Rich
    Actual air fuel ratio rich
    Lean
    Lean/Rich
    A/F sensor malfunction
    B
    Rich
    Lean/Rich
    A/F sensor malfunction
    Lean/Rich
    Lean/Rich
    Normal
    Lean: During Control the Injection Volume for A/F Sensor Active Test, the A/F sensor output voltage (AFS Voltage B1S1 or B2S1) is consistently more than 3.4 V, and the HO2 output voltage (O2S B1S2 or B2S2) is consistently less than 0.4 V.
    Rich: During Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage B1S1 or B2S1 is consistently less than 3.1 V, and the O2S B1S2 or B2S2 is consistently more than 0.55 V.
    Lean/Rich: During Control the Injection Volume for A/F Sensor Active Test, the output voltage of the A/F sensor and HO2 sensor alternates correctly.

    HINT:
    Refer to "Data List / Active Test" [AFS Voltage B1S1, AFS Voltage B2S1, O2S B1S2 and O2S B2S2] (Click here).



B
Go to step 14
A


6.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leak (Click here).

    OK:
    No leak from intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


7.CHECK EXHAUST GAS LEAK
  1. Check the exhaust gas leaks.

    OK:
    No exhaust gas leaks.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


8.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 16
OK


9.INSPECT FUEL INJECTOR ASSEMBLY
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


10.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the A/F sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).


NEXT


11.PERFORM CONFIRMATION DRIVING PATTERN
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2195, P2196, P2197 or P2198.

  1. Check the DTC judgment.
    Result 
    Result
    Proceed to
    ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output)
    A
    NORMAL (DTC is not output)
    B



B
END
A


12.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


13.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2195, P2196, P2197 or P2198.

  1. Check the DTC judgment.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit


NEXT

END 

14.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the A/F sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).


NEXT


15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2195, P2196, P2197 or P2198.

  1. Check the DTC judgment.
    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P2195, P2196, P2197 or P2198 are output)
    B



B
REPLACE ECM (Click here)
A

END 

16.CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage.

    HINT:
    Perform "Inspection After Repair" after replacing the fuel pump (Click here).



NG
REPAIR OR REPLACE FUEL SYSTEM
OK

REPLACE FUEL PUMP (Click here)