Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1790    Center Airbag Sensor Assembly Communication Circuit Malfunction

for Preparation Click here


DESCRIPTION

The center airbag sensor assembly communication circuit consists of the occupant classification ECU and the center airbag sensor assembly.
DTC B1790 is recorded when a malfunction is detected in the center airbag sensor assembly communication circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1790
  1. Occupant classification ECU detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the center airbag sensor assembly communication circuit for 2 seconds
  2. Center airbag sensor assembly malfunction
  3. Occupant classification ECU malfunction
  1. No. 1 Seat wire
  2. Floor wire
  3. Occupant classification ECU
  4. Center airbag sensor assembly

WIRING DIAGRAM


H102282E05


INSPECTION PROCEDURE

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see the under surface of the seat cushion.
  2. In the above case, hold the seat so that it does not tip over. Holding the seat for a long period of time may cause a problem, such as seat rail deformation. Hold the seat up only for as long as necessary.

1.CHECK DTC
  1. Turn the ignition switch to the on position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch to the lock position.

  1. Turn the ignition switch to the on position.

  1. Check the DTCs (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    Codes other than DTC B1790 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK (Click here)
NG


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the lock position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and the center airbag sensor assembly.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3.CHECK CENTER AIRBAG SENSOR CIRCUIT (TO B+)


    H102277E01
  1. Disconnect the connectors from the occupant classification ECU and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the on position.

  1. Measure the voltage.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    Q4-8 (FSR+) -
    Body ground
    Ignition switch on
    Below 1 V
    Q4-4 (FSR-) -
    Body ground
    Ignition switch on
    Below 1 V



NG
Go to step 12
OK


4.CHECK CENTER AIRBAG SENSOR CIRCUIT (FOR OPEN)


    C193521E01
  1. Turn the ignition switch to the lock position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect K1-16 (FSP+) and K1-24 (FSP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    Q4-8 (FSR+) -
    Q4-4 (FSR-)
    Always
    Below 1 Ω



NG
Go to step 13
OK


5.CHECK CENTER AIRBAG SENSOR CIRCUIT (FOR SHORT)


    H102277E01
  1. Disconnect the service wire from connector B.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    Q4-8 (FSR+) -
    Q4-4 (FSR-)
    Always
    1 MΩ or higher



NG
Go to step 14
OK


6.CHECK CENTER AIRBAG SENSOR CIRCUIT (TO GROUND)


    H102277E01
  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    Q4-8 (FSR+) -
    Body ground
    Always
    1 MΩ or higher
    Q4-4 (FSR-) -
    Body ground
    Always
    1 MΩ or higher



NG
Go to step 15
OK


7.CHECK DTC
  1. Connect the connectors to the occupant classification ECU and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the on position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch to the lock position.

  1. Turn the ignition switch to the on position.

  1. Check the DTCs (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    Codes other than DTC B1790 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK (Click here)
NG


8.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch to the lock position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


9.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch to the on position.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed.


NEXT


10.PERFORM SENSITIVITY CHECK
  1. Using a Techstream, perform the sensitivity check (Click here).

    1. Confirm that nothing is placed on the passenger seat.

    2. Confirm that the beginning sensor reading is within the standard range.

      Standard range:
      -3.2 to 3.2 kg (-7 to 7 lb)

    3. Place a 30 kg (66.14 lb) weight (e.g. a lead mass) onto the front passenger seat.

    4. Confirm that the sensitivity is within the standard range.

      Standard range:
      27 to 33 kg (59.52 to 72.75 lb)

      HINT:
      When performing the sensitivity check, use a solid metal weight (the check result may not be accurate if a liquid weight is used).


NEXT


11.CHECK DTC
  1. Turn the ignition switch to the on position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch to the lock position.

  1. Turn the ignition switch to the on position.

  1. Check the DTCs (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    Codes other than DTC B1790 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END 

12.CHECK FLOOR WIRE (TO B+)


    H102279E01
  1. Turn the ignition switch to the lock position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the floor wire and the No. 1 seat wire.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the on position.

  1. Measure the voltage.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    KQ1-1 (FSR+) -
    Body ground
    Ignition switch on
    Below 1 V
    KQ1-4 (FSR-) -
    Body ground
    Ignition switch on
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPLACE NO.1 SEAT WIRE 

13.CHECK FLOOR WIRE (FOR OPEN)


    C193522E01
  1. Disconnect the connectors from the floor wire and the No. 1 seat wire.

    HINT:
    The service wire has already been inserted into connector B.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    KQ1-1 (FSR+) -
    KQ1-4 (FSR-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPLACE NO.1 SEAT WIRE 

14.CHECK FLOOR WIRE (FOR SHORT)


    H102279E01
  1. Disconnect the connectors from the floor wire and the No. 1 seat wire.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    KQ1-1 (FSR+) -
    KQ1-4 (FSR-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPLACE NO.1 SEAT WIRE 

15.CHECK FLOOR WIRE (TO GROUND)


    H102279E01
  1. Disconnect the connectors from the floor wire and the No. 1 seat wire.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    KQ1-1 (FSR+) -
    Body ground
    Always
    1 MΩ or higher
    KQ1-4 (FSR-) -
    Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPLACE NO.1 SEAT WIRE