DTC P0500 Vehicle Speed Sensor |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0500 | While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (2 trip detection logic) |
|
| Related DTCs | P0500: Vehicle speed sensor "A" pulse input error |
| Required Sensors/Components (Main) | Vehicle speed sensor, Combination meter assembly, Skid control ECU |
| Required Sensors/Components (Related) | Park/neutral position switch assembly*, Engine coolant temperature sensor, Crankshaft position sensor, Mass air flow meter, Throttle position sensor |
| Frequency of Operation | Continuous |
| Duration | 5 seconds: for automatic transmission models 4.566 seconds: for manual transmission models |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Ignition switch | ON |
| Time after ignition switch off to ON | 3 seconds or more |
| Battery voltage | 8 V or more |
| Starter | OFF |
| Idle | ON |
| Fuel cut | ON |
| Battery voltage | 8 V or more |
| Starter | OFF |
| Time after ignition switch off to ON | 3 seconds or more |
| Vehicle speed at output speed sensor | 9 km/h (5.59 mph) or more |
| Transfer neutral position switch | OFF |
| Vehicle speed sensor signal | No signal |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK OPERATION OF SPEEDOMETER |
Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (VEHICLE SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the Techstream.
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM) |
Disconnect the combination meter assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E13-14 (+S) - E78-18 (SPD) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| E13-14 (+S) or E78-18 (SPD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT COMBINATION METER ASSEMBLY (VOLTAGE) |
![]() |
Disconnect the combination meter assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E13-14 (+S) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
|
| ||||
| OK | |
| 5.INSPECT COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM) |
![]() |
Move the shift lever to neutral position.
Jack up the vehicle.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E78-18 (SPD) - B49-12 (E1) | Ignition switch ON (Turn wheel slowly) | Voltage generated intermittently |
| *a | Component with harness connected (ECM) |
| *b | Turn Wheel |
|
| ||||
| OK | ||
| ||
| 6.INSPECT COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM) |
![]() |
Remove the combination meter assembly (Click here).
Connect the combination meter assembly connector.
Move the shift lever to the neutral position.
Jack up the vehicle.
Turn the ignition switch to ON.
Check the voltage between the terminal of the combination meter assembly and the body ground while the wheel is turned slowly.
| Tester Connection | Switch Condition | Specified Condition |
| E13-13 (SI) - Body ground | Ignition switch ON (Turn wheel slowly) | Voltage generated intermittently |
| *a | Component with harness connected (Combination Meter Assembly) |
| *b | Turn Wheel |
Reinstall the combination meter assembly (Click here).
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HYDRAULIC BRAKE BOOSTER) |
Disconnect the combination meter assembly connector.
Disconnect the hydraulic brake booster connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E13-13 (SI) - A4-12 (SP1) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| E13-13 (SI) or A4-12 (SP1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||