Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

DTC    01-D6    No Master

DTC    01-D7    Connection Check Error

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
01-D6*1
Either condition is met:
  1. The device that stores (stored) the DTC has (had) been disconnected while the ignition switch is ACC or ON.
  2. The master device has (had) been disconnected when this DTC is stored.
  1. Radio receiver assembly power source circuit
  2. Power source circuit of the component which has stored this code
  3. AVC-LAN circuit between the radio receiver assembly and component which has stored this code
  4. Component which has stored this code
  5. Radio receiver assembly
01-D7*2
Either condition is met:
  1. The device that stored the code has (had) been disconnected after the engine starts (started).
  2. The master device has (had) been disconnected when this DTC is (was) stored.

HINT:
  1. *1: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. *2: When 210 seconds have elapsed after disconnecting the power supply connector of the master component with the ignition switch to ACC or ON, this DTC is stored.

NOTICE:
  1. Before starting troubleshooting, be sure to clear the DTCs stored due to the reasons described in the HINT above. Then, check for DTCs and troubleshoot according to the output DTCs.
  2. The radio receiver assembly is the master unit.
  3. Be sure to clear and recheck for the DTCs after the inspection is completed to confirm that no DTCs are output.


INSPECTION PROCEDURE

NOTICE:
Be sure to read Description before performing the following procedure.

1.CHECK RADIO RECEIVER ASSEMBLY POWER SOURCE CIRCUIT

HINT:
Refer to Radio Receiver Power Source Circuit (Click here).

If the power source circuit is operating normally, proceed to the next step.

NEXT


2.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE


  1. Enter diagnostic mode.


    E110915E13

  1. Press preset switch "2" to change the mode to "Detailed Information Mode".

  1. Identify the component which has stored this code.

    Component Table 
    Component
    Physical Address
    Stereo component amplifier assembly*1
    440
    Satellite radio tuner
    1F83
    Multi-media interface ECU
    388
    *1: w/ Stereo Component Amplifier Assembly

    HINT:
    1. "P440" set by the stereo component amplifier assembly shown in the preceding illustration as an example.
    2. For details of the DTC display, refer to DTC Check/Clear (Click here).


NEXT


3.CHECK COMPONENT SHOWN BY SUB-CODE
  1. Select the component shown by the sub-code.

    HINT:
    The satellite radio tuner is built into the radio receiver assembly. If there is a problem between the satellite radio tuner and radio receiver assembly, replace the radio receiver assembly.


    Component Table 
    Component
    Proceed to
    Except radio receiver assembly
    A
    Radio receiver assembly (190)
    B



B
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
A


4.CHECK POWER SOURCE CIRCUIT OF COMPONENT WHICH HAS STORED THIS CODE
  1. Inspect the power source circuit of the component which has stored this code.
    If the power source circuit is operating normally, proceed to the next step.

    Component Table 
    Component
    Proceed to
    Stereo component amplifier assembly*1
    Stereo component amplifier power source circuit (Click here)
    Multi-media interface ECU
    Multi-media interface ECU power source circuit (Click here)
    *1: w/ Stereo Component Amplifier Assembly


NEXT


5.INSPECT RADIO RECEIVER ASSEMBLY


    E194165E06
  1. Disconnect the E83*1 and E84 radio receiver assembly connectors.
    *1: w/ Stereo Component Amplifier Assembly

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    5 (ATX+) - 15 (ATX-)*1
    Always
    60 to 80 Ω
    9 (TXM+) - 10 (TXM-)
    Always
    60 to 80 Ω

    *1: w/ Stereo Component Amplifier Assembly
    Text in Illustration 
    *a
    Component without harness connected
    (Radio Receiver Assembly (w/ Stereo Component Amplifier Assembly))
    *b
    Component without harness connected
    (Radio Receiver Assembly)



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR

HINT:
For details of the connectors, refer to Terminals of ECU (Click here).



  1. Referring to the following AVC-LAN wiring diagram, check the AVC-LAN circuit between the radio receiver assembly and the component which has stored this code.

    1. Disconnect all connectors between the radio receiver assembly and component which has stored this code.



    2. Check for an open or short in the AVC-LAN circuit between the radio receiver assembly and component which has stored this code.

      OK:
      There is no open or short circuit.


      E194159E10



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE COMPONENT WHICH HAS STORED THIS CODE
  1. Replace the component which has stored this code with a known good one.


NEXT


8.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


9.RECHECK FOR DTC
  1. Recheck for DTCs and check if the same problem occurs again.

    OK:
    Malfunction disappears.



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK

END