DTC B1628/82 Side Airbag Sensor Assembly LH Initialization Incomplete |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1628/82 |
|
|

| 1.CHECK HISTORY DTC |
Check for history DTCs (Click here).
| Result | Proceed to |
| History DTC B1627/82 is not output. | A |
| History DTC B1627/82 is output. | B |
|
| ||||
| A | |
| 2.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the center airbag sensor assembly and side airbag sensor assembly LH.
Disconnect the connectors from the center airbag sensor assembly and side airbag sensor assembly LH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 3.CHECK NO. 2 FLOOR WIRE (OPEN) |
![]() |
Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L4-4 (BBL+) - L4-3 (BBL-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Center Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Center Airbag Sensor Assembly) |
| *b | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 4.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L4-4 (BBL+) - Body ground | Always | 1 MΩ or higher |
| L4-3 (BBL-) - Body ground | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Center Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 5.CHECK NO. 2 FLOOR WIRE (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L4-4 (BBL+) - L4-3 (BBL-) | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Center Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 6.CHECK NO. 2 FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L4-4 (BBL+) - Body ground | Ignition switch ON | Below 1 V |
| L4-3 (BBL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Center Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 7.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH |
![]() |
Connect the connector to the center airbag sensor assembly.
Interchange the side airbag sensor assembly LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTCs B1623/81 and B1628/82 are not output. | A |
| DTC B1628/82 is output. | B |
| DTC B1623/81 is output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Center Airbag Sensor Assembly |
|
| ||||
|
| ||||
| A | ||
| ||