DTC B1637/82 Lost Communication with Rear Airbag Sensor LH |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1637/82 |
|
|
| 1.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the side airbag sensor assembly LH and rear airbag sensor LH.
Disconnect the connectors from the side airbag sensor assembly LH and rear airbag sensor LH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 2.CHECK NO. 2 FLOOR WIRE (OPEN) |
![]() |
Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L4-1 (BCL+) - L4-2 (BCL-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| *1 | Rear Airbag Sensor LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | No. 2 Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
| *b | Front view of wire harness connector (to Rear Airbag Sensor LH) |
|
| ||||
| OK | |
| 3.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L4-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| L4-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
| *1 | Rear Airbag Sensor LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 4.CHECK NO. 2 FLOOR WIRE (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L4-1 (BCL+) - L4-2 (BCL-) | Always | 1 MΩ or higher |
| *1 | Rear Airbag Sensor LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 5.CHECK NO. 2 FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L4-1 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| L4-2 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
| *1 | Rear Airbag Sensor LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 6.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH |
![]() |
Connect the connector to the rear airbag sensor LH.
Interchange the side airbag sensor assembly LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1637/82 is output. | A |
| DTC B1632/81 is output. | B |
| DTCs B1632/81 and B1637/82 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Center Airbag Sensor Assembly |
|
| ||||
|
| ||||
| A | |
| 7.CHECK REAR AIRBAG SENSOR LH |
![]() |
Interchange the rear airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTCs B1632/81 and B1637/82 are not output. | A |
| DTC B1637/82 is output. | B |
| DTC B1632/81 is output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the rear airbag sensor LH and RH to their original positions and connect the connectors.
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly LH |
|
| ||||
|
| ||||
| A | ||
| ||