DTC B1633/81 Rear Airbag Sensor Assembly RH Initialization Incomplete |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1633/81 |
|
|
| 1.CHECK HISTORY DTC |
Check for history DTCs (Click here).
| Result | Proceed to |
| History DTC B1632/81 is not output. | A |
| History DTC B1632/81 is output. | B |
|
| ||||
| A | |
| 2.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the side airbag sensor assembly RH and rear airbag sensor RH.
Disconnect the connectors from the side airbag sensor assembly RH and rear airbag sensor RH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 3.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
![]() |
Connect the connector to the rear airbag sensor RH.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1633/81 is output. | A |
| DTC B1638/82 is output. | B |
| DTCs B1633/81 and B1638/82 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Center Airbag Sensor Assembly |
|
| ||||
|
| ||||
| A | |
| 4.CHECK FLOOR WIRE (OPEN) |
![]() |
Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K2-1 (BCR+) - K2-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector (to Rear Airbag Sensor RH) |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K2-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| K2-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 6.CHECK FLOOR WIRE (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K2-1 (BCR+) - K2-2 (BCR-) | Always | 1 MΩ or higher |
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 7.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| K2-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| K2-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 8.CHECK REAR AIRBAG SENSOR RH |
![]() |
Interchange the rear airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTCs B1633/81 and B1638/82 are not output. | A |
| DTC B1633/81 is output. | B |
| DTC B1638/82 is output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the rear airbag sensor RH and LH to their original positions and connect the connectors.
| *1 | Rear Airbag Sensor LH |
| *2 | Side Airbag Sensor Assembly RH |
|
| ||||
|
| ||||
| A | ||
| ||