Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Lines for Short Circuit

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
  1. Short between CAN bus lines
  2. ECM
  3. Airbag sensor assembly
  4. Combination meter assembly (combination meter ECU)
  5. Yaw rate sensor
  6. Master cylinder solenoid (skid control ECU)
  7. Steering angle sensor
  8. Driving support switch control ECU*1
  9. CAN junction connector
  1. *1: w/ CRAWL

WIRING DIAGRAM


E257629E05


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the ignition switch off before inspecting CAN bus wires for a ground short.
  3. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE)


    E194173E22
  1. Disconnect the E86 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-14 (CANL)
    Ignition switch off
    1 MΩ or higher

Text in Illustration 
*a
Front view of DLC3


NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


4.CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR - YAW RATE SENSOR)


    E211086E44
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-2 (CANH) - E86-13 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)



NG
Go to step 12
OK


5.CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    E211086E43
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-5 (CANH) - E86-16 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)



NG
Go to step 14
OK


6.CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR - MASTER CYLINDER SOLENOID (SKID CONTROL ECU))


    E211086E41
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-6 (CANH) - E86-17 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)



NG
Go to step 16
OK


7.CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)


    E211086E45
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-7 (CANH) - E86-18 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)



NG
Go to step 18
OK


8.SYSTEM CHECK
  1. Check the vehicle specifications.
    Result 
    Result
    Proceed to
    w/ CRAWL
    A
    w/o CRAWL
    B



B
Go to step 10
A


9.CHECK SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR - DRIVING SUPPORT SWITCH CONTROL ECU)


    E211086E58
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal No. (Symbol)
    Switch Condition
    Specified Condition
    E86-8 (CANH) - E86-19 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)



NG
Go to step 20
OK


10.CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR - ECM)


    E211086E46
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-1 (CANH) - E86-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)



NG
Go to step 22
OK


11.CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR - COMBINATION METER ECU)


    E211086E42
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-3 (CANH) - E86-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)



NG
Go to step 24
OK

REPLACE CAN JUNCTION CONNECTOR 

12.CONNECT CONNECTOR
  1. Reconnect the E86 CAN junction connector connector.


NEXT


13.CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR)


    E175983E06
  1. Disconnect the yaw rate sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E81-3 (CANH) - E81-2 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE YAW RATE SENSOR (Click here)  

14.CONNECT CONNECTOR
  1. Reconnect the E86 CAN junction connector connector.


NEXT


15.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)


    E192049E04
  1. Disconnect the steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-3 (CANH) - E16-11 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE STEERING ANGLE SENSOR (Click here)  

16.CONNECT CONNECTOR
  1. Reconnect the E86 CAN junction connector connector.


NEXT


17.CHECK FOR SHORT IN CAN BUS WIRES (MASTER CYLINDER SOLENOID (SKID CONTROL ECU))
E191994E04
  1. Disconnect the master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-11 (CANH) - A4-25 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid (Skid Control ECU))



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)  

18.CONNECT CONNECTOR
  1. Reconnect the E86 CAN junction connector connector.


NEXT


19.CHECK FOR SHORT IN CAN BUS WIRES (AIRBAG SENSOR ASSEMBLY)


    E186790E14
  1. Disconnect the airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E29-13 (CANH) - E29-22 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

20.CONNECT CONNECTOR
  1. Reconnect the E86 CAN junction connector.


NEXT


21.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT SWITCH CONTROL ECU)


    E257628E06
  1. Disconnect the driving support switch control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal No. (Symbol)
    Switch Condition
    Specified Condition
    E89-8 (CANH) - E89-3 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Driving Support Switch Control ECU))



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU (Click here)  

22.CONNECT CONNECTOR
  1. Reconnect the E86 CAN junction connector connector.


NEXT


23.CHECK FOR SHORT IN CAN BUS WIRES (ECM)


    E214877E01
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E77-32 (CANH) - E77-31 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE ECM (Click here)  

24.CONNECT CONNECTOR
  1. Reconnect the E86 CAN junction connector connector.


NEXT


25.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY (COMBINATION METER ECU))


    E214880E01
  1. Disconnect the combination meter assembly (combination meter ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E14-10 (CANH) - E14-9 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly (Combination Meter ECU))



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE COMBINATION METER ASSEMBLY (COMBINATION METER ECU) (Click here)