Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to +B

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus line and +B when there is resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.

Symptom
Trouble Area
There is resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.
  1. Short to +B
  2. ECM
  3. Airbag sensor assembly
  4. Combination meter assembly (combination meter ECU)
  5. Yaw rate sensor
  6. Master cylinder solenoid (skid control ECU)
  7. Steering angle sensor
  8. Driving support switch control ECU*1
  9. CAN junction connector
  1. *1: w/ CRAWL

WIRING DIAGRAM


E257629E05


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the ignition switch off before inspecting CAN bus wires for a ground short.
  3. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 BRANCH WIRE)


    E194173E23
  1. Disconnect the E86 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E1-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - YAW RATE SENSOR)


    E214883E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-2 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E86-13 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 12
OK


5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    E214883E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-5 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E86-16 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 13
OK


6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - MASTER CYLINDER SOLENOID (SKID CONTROL ECU))


    E214883E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E86-17 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 14
OK


7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)


    E214883E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-7 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E86-18 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 15
OK


8.SYSTEM CHECK
  1. Check the vehicle specifications.
    Result 
    Result
    Proceed to
    w/ CRAWL
    A
    w/o CRAWL
    B



B
Go to step 10
A


9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - DRIVING SUPPORT SWITCH CONTROL ECU)


    E214883E25
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal No. (Symbol)
    Switch Condition
    Specified Condition
    E86-8 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E86-19 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 16
OK


10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - ECM)


    E214883E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-1 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E86-12 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 17
OK


11.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY (COMBINATION METER ECU))


    E214883E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-3 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E86-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 18
OK

REPLACE CAN JUNCTION CONNECTOR 

12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR)


    E214883E04
  1. Disconnect the E81 yaw rate sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-2 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E86-13 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE YAW RATE SENSOR (Click here)  

13.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR)


    E214883E03
  1. Disconnect the E16 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-5 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E86-16 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE STEERING ANGLE SENSOR (Click here)  

14.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MASTER CYLINDER SOLENOID (SKID CONTROL ECU))
E214883E01
  1. Disconnect the A4 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-6 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E86-17 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)  

15.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY)


    E214883E05
  1. Disconnect the E29 airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-7 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E86-18 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DRIVING SUPPORT SWITCH CONTROL ECU)


    E214883E25
  1. Disconnect the E89 driving support switch control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal No. (Symbol)
    Switch Condition
    Specified Condition
    E86-8 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E86-19 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CNA-H, CAN-L)
OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU (Click here)  

17.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM MAIN WIRE)


    E214883E06
  1. Disconnect the E77 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-1 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E86-12 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE ECM (Click here)  

18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY (COMBINATION METER ECU))


    E214883E02
  1. Disconnect the E14 combination meter assembly (combination meter ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E86-3 (CANH) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E86-14 (CANL) - E1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)