CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to GND |
| Symptom | Trouble Area |
| There is resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3. |
|

| 1.PRECAUTION |
| NEXT | |
| 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
| NEXT | |
| 3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 BRANCH WIRE) |
![]() |
Disconnect the E86 CAN junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E1-6 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E1-14 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
|
| ||||
| OK | |
| 4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - YAW RATE SENSOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E86-2 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E86-13 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to CAN Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - STEERING ANGLE SENSOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E86-5 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E86-16 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to CAN Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - MASTER CYLINDER SOLENOID (SKID CONTROL ECU)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E86-6 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E86-17 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to CAN Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E86-7 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E86-18 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to CAN Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 8.SYSTEM CHECK |
Check the vehicle specifications.
| Result | Proceed to |
| w/ CRAWL | A |
| w/o CRAWL | B |
|
| ||||
| A | |
| 9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - DRIVING SUPPORT SWITCH CONTROL ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Switch Condition | Specified Condition |
| E86-8 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E86-19 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to CAN Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E86-1 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E86-12 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to CAN Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY (COMBINATION METER ECU)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E86-3 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E86-14 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to CAN Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (YAW RATE SENSOR) |
![]() |
Disconnect the E81 yaw rate sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E86-2 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E86-13 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to CAN Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR) |
Disconnect the E16 steering angle sensor connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E86-5 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E86-16 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to CAN Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (MASTER CYLINDER SOLENOID (SKID CONTROL ECU)) |
Disconnect the A4 master cylinder solenoid (skid control ECU) connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E86-6 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E86-17 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to CAN Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY) |
![]() |
Disconnect the E29 airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E86-7 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E86-18 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to CAN Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DRIVING SUPPORT SWITCH CONTROL ECU) |
![]() |
Disconnect E89 driving support switch control ECU.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Switch Condition | Specified Condition |
| E86-8 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E86-19 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to CAN Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM MAIN WIRE) |
![]() |
Disconnect the E77 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E86-1 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E86-12 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to CAN Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY (COMBINATION METER ECU)) |
![]() |
Disconnect the E14 combination meter assembly (combination meter ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E86-3 (CANH) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| E86-14 (CANL) - E1-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to CAN Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||