Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Crawl Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

When crawl control starts after operating the crawl switch, the crawl indicator light turns on.

WIRING DIAGRAM

Refer to Crawl Indicator Light does not Come ON .

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


2.READ VALUE USING TECHSTREAM (CRAWL CONTROL SWITCH ASSEMBLY)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / D-SEAT SW / Data List.

  1. According to the display on the Techstream, read the Data List.

    D-SEAT SW 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Crawl Control Main Switch
    Crawl control switch (ON/OFF switch)/ ON or OFF
    ON: Crawl switch on
    OFF: Crawl switch off
    -

    OK:
    The Techstream displays ON or OFF according to crawl control switch operation.



NG
Go to step 5
OK


3.READ VALUE USING TECHSTREAM (CRAWL CONTROL SWITCH ASSEMBLY)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/ TRAC / Data List.

  1. According to the display on the Techstream, read the Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Crawl Control Light
    Crawl indicator light/ ON or OFF
    ON: Indicator light on
    OFF: Indicator light off
    -
    Crawl Control Switch
    Crawl speed selector switch status/ LOW, MIDLOW, MID, MIDHIGH or HIGH
    Actual crawl speed selector switch position
    -

    OK:
    The Techstream displays ON or OFF according to switch operation.



NG
Go to step 9
OK


4.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Perform Active Test of the combination meter using the Techstream (Click here).

  1. Check that the CRAWL indicator light turns on and off on the combination meter when using the Techstream.

    OK:
    The CRAWL indicator light turns ON or OFF according to the Techstream operations.



NG
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)  

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C269715E04
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the driving support switch control ECU connector.

  1. Check the connector case and terminals for deformation and corrosion.

    Standard condition:
    No deformation or corrosion.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E89-2 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    E89-6 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Driving Support Switch Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


6.CHECK HARNESS AND CONNECTOR (GND TERMINAL)


    C269715E05
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E89-16 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Driving Support Switch Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND TERMINAL)
OK


7.CHECK HARNESS AND CONNECTOR (CRAWL CONTROL SWITCH ASSEMBLY - DRIVING SUPPORT SWITCH CONTROL ECU)
  1. Disconnect the M3 crawl control switch assembly connector.

  1. Disconnect the E89 driving support switch control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M3-5 (SWI1) - E89-10 (SWO1)
    Always
    Below 1 Ω
    M3-5 (SWI1) - Body ground
    Always
    10 kΩ or higher
    E89-10 (SWO1) - Body ground
    Always
    10 kΩ or higher
    M3-6 (SWO2) - E89-12 (SWI2)
    Always
    Below 1 Ω
    M3-6 (SWO2) - Body ground
    Always
    10 kΩ or higher
    E89-12 (SWI2) - Body ground
    Always
    10 kΩ or higher
    M3-2 (SWI3) - E89-14 (SWO3)
    Always
    Below 1 Ω
    M3-2 (SWI3) - Body ground
    Always
    10 kΩ or higher
    E89-14 (SWO3) - Body ground
    Always
    10 kΩ or higher
    M3-8 (SWO4) - E89-4 (SWI4)
    Always
    Below 1 Ω
    M3-8 (SWO4) - Body ground
    Always
    10 kΩ or higher
    E89-4 (SWI4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT CRAWL CONTROL SWITCH ASSEMBLY
  1. Remove the crawl control switch assembly (Click here).

  1. Inspect the crawl control switch assembly (Click here).



NG
REPLACE CRAWL CONTROL SWITCH ASSEMBLY (Click here)
OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU (Click here)  

9.CHECK HARNESS AND CONNECTOR (CRAWL CONTROL SWITCH ASSEMBLY - DRIVING SUPPORT SWITCH CONTROL ECU)
  1. Disconnect the M3 crawl control switch assembly connector.

  1. Disconnect the E89 driving support switch control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M3-5 (SWI1) - E89-10 (SWO1)
    Always
    Below 1 Ω
    M3-5 (SWI1) - Body ground
    Always
    10 kΩ or higher
    E89-10 (SWO1) - Body ground
    Always
    10 kΩ or higher
    M3-6 (SWO2) - E89-12 (SWI2)
    Always
    Below 1 Ω
    M3-6 (SWO2) - Body ground
    Always
    10 kΩ or higher
    E89-12 (SWI2) - Body ground
    Always
    10 kΩ or higher
    M3-2 (SWI3) - E89-14 (SWO3)
    Always
    Below 1 Ω
    M3-2 (SWI3) - Body ground
    Always
    10 kΩ or higher
    E89-14 (SWO3) - Body ground
    Always
    10 kΩ or higher
    M3-8 (SWO4) - E89-4 (SWI4)
    Always
    Below 1 Ω
    M3-8 (SWO4) - Body ground
    Always
    10 kΩ or higher
    E89-4 (SWI4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT CRAWL CONTROL SWITCH ASSEMBLY
  1. Remove the crawl control switch assembly (Click here).

  1. Inspect the crawl control switch assembly (Click here).



NG
REPLACE CRAWL CONTROL SWITCH ASSEMBLY (Click here)
OK


11.REPLACE DRIVING SUPPORT SWITCH CONTROL ECU
  1. Replace the driving support switch control ECU (Click here).


NEXT


12.READ VALUE USING TECHSTREAM (CRAWL CONTROL SWITCH ASSEMBLY)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/ TRAC / Data List.

  1. According to the display on the Techstream, read the Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Crawl Control Light
    Crawl indicator light/ ON or OFF
    ON: Indicator light on
    OFF: Indicator light off
    -
    Crawl Control Switch
    Crawl speed selector switch status/ LOW, MIDLOW, MID, MIDHIGH or HIGH
    Actual crawl speed selector switch position
    -

    OK:
    The Techstream displays ON or OFF according to switch operation.



NG
REPLACE MASTER CYLINDER SOLENOID (Click here)
OK

END