2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Dec 2017

Versions by build date: Oct 2014 – Nov 2017 from Dec 2017

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Air Conditioning System)
  1. Start up the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor at an engine rpm of approximately 1,000 for 5 to 6 minutes to circulate the refrigerant and collect compressor oil remaining in each component into the cooler compressor as much as possible.

  1. Stop the engine.

  1. Using SST, let the refrigerant gas out.

    SST
    07110-58060   (07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

4. REMOVE NO. 1 ENGINE UNDER COVER (for Cold Area Specification Vehicles)
  1. Remove the 4 bolts and No. 1 engine under cover.


5. REMOVE NO. 2 ENGINE UNDER COVER (for Cold Area Specification Vehicles)
  1. Remove the 6 bolts and No. 2 engine under cover.


6. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    A316609E01

    Text in Illustration 
    *1
    Bleeder Plug
    *2
    Radiator Reservoir Cap Sub-assembly
    *3
    Radiator Reservoir Assembly
    *4
    Cylinder Block Drain Cock Plug
    *5
    Radiator Drain Cock Plug
    -
    -

  1. Remove the radiator reservoir cap sub-assembly.

  1. Loosen the cylinder block drain cock plug (on the engine oil cooler cover), and drain the engine coolant.

  1. Tighten the radiator drain cock plug.

  1. Tighten the cylinder block drain cock plug (on the engine oil cooler cover).

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


7. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Wipe the oil pan and oil pan drain plug.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }


8. DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission)
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the oil.

  1. Install the drain plug with a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


9. DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

  1. C158131E01
    Remove the drain plug and gasket and drain automatic transmission fluid.

  1. Install the drain plug with a new gasket.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


10. REMOVE FRONT SEAT ASSEMBLY RH

  1. B107528
    Move the front seat assembly fully forward.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Move the front seat assembly to the rearmost position.

  1. Remove the 2 bolts on the front side of the seat.

  1. Move the front seat assembly to the center of the seat slide rail. Set the seatback in the upright position.

  1. Disconnect the front seat inner belt assembly connector.

  1. Remove the front seat assembly.


11. REMOVE FRONT DOOR SCUFF PLATE RH

12. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Roll up the carpet and remove the engine service hole sub cover.


13. REMOVE NO. 2 ENGINE SERVICE HOLE COVER (for Standard Body)
  1. Detach the clips and fold back the carpet.

  1. A151559
    Remove the 3 bolts and No. 2 engine service hole cover.


14. REMOVE FAN AND GENERATOR V BELT

  1. A156649E01
    Remove the drive belt by rotating the tensioner pulley clockwise to loosen its tension with the pulley set bolt of the tensioner.


15. REMOVE FAN PULLEY
  1. Remove the 4 nuts and fan pulley.


16. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)

17. REMOVE NO. 1 AIR CLEANER HOSE

  1. A153649
    Pull the stopper upward and disconnect the No. 1 air cleaner hose from the compressor inlet elbow.


18. REMOVE AIR TUBE ASSEMBLY

  1. A272217
    Loosen the 2 hose clamps.

  1. Remove the 2 bolts, air tube assembly and No. 1 air cleaner hose.


19. REMOVE COMPRESSOR OUTLET ELBOW

  1. A313566
    Loosen the 2 hose clamps and remove the bolt and compressor outlet elbow.


20. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

  1. A102453E01
    Remove the 4 bolts and No. 1 compressor mounting bracket.


21. REMOVE NO. 2 IDLE PULLEY ASSEMBLY (w/ Air Conditioning System)
  1. Remove the bolt, pulley plate, No. 2 idle pulley and spacer.


22. REMOVE GENERATOR ASSEMBLY
(Click here)

23. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A102857
    Remove the 4 bolts and V-ribbed belt tensioner.


24. REMOVE TURBOCHARGER SUB-ASSEMBLY
(Click here)

25. REMOVE EXHAUST MANIFOLD

  1. A239347
    Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.


26. DISCONNECT OIL RETURN HOSE
  1. Disconnect the oil return hose from the intake manifold.


27. REMOVE NO. 4 AIR HOSE
  1. Remove the No. 4 air hose from the diesel throttle body.


28. DISCONNECT RADIATOR HOSE INLET
  1. Disconnect the radiator hose inlet from the water outlet.


29. DISCONNECT NO. 4 RADIATOR HOSE
  1. Disconnect the No. 4 radiator hose from the water inlet.


30. DISCONNECT NO. 2 FUEL HOSE
  1. Disconnect the No. 2 fuel hose from the No. 2 nozzle leakage pipe.


31. DISCONNECT NO. 1 FUEL HOSE
  1. Disconnect the No. 1 fuel hose from the fuel supply pump.


32. DISCONNECT VACUUM HOSE

  1. A038767E01
    Disconnect the vacuum hose from the vacuum pump.


33. DISCONNECT ENGINE WIRE

  1. A239339
    Remove the bolt.

  1. A320193
    Disconnect the ECM connector (Click here).

  1. Disconnect the 4 connectors.

  1. Detach the 3 clamps.


34. DISCONNECT ENGINE ROOM MAIN WIRE

  1. A239344
    Disconnect the 5 connectors.

  1. A239345
    Open the cover and remove the nut.

  1. A239343
    Detach the clamp and disconnect the engine room main wire.


35. DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

  1. A231913
    Remove the 2 bolts and disconnect the vane pump oil reservoir.


36. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
(Click here)

37. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)

38. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. C114267E01
    Put matchmarks on the clutch cover assembly and the flywheel sub-assembly.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the set bolts, and pull off the clutch cover assembly.

    NOTICE:
    Do not drop the clutch disc assembly.


39. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

NOTICE:
Keep the lining part of the clutch disc assembly, the pressure plate and surface of the flywheel sub-assembly away from oil and foreign matter.


40. REMOVE FLYWHEEL SUB-ASSEMBLY

  1. A072851E03
    Hold the crankshaft pulley with SST.
    SST
    09213-58014  
    09330-00021  

  1. A242999E01
    for Manual Transmission:
    Remove the 8 bolts and flywheel.

  1. for Automatic Transmission:
    Remove the 8 bolts, rear drive plate spacer, pump impeller drive plate and flywheel.


41. REMOVE REAR END PLATE
  1. Remove the bolt and rear end plate.


42. REMOVE SPEED SENSOR FRONT LH (w/ ABS)

  1. C102281E01
    Remove the 2 bolts, and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Be careful not to damage the speed sensor.
    2. Prevent foreign matter from adhering to the speed sensor.


43. REMOVE SPEED SENSOR FRONT RH (w/ ABS)

HINT:
Use the same procedures described for the LH side.


44. REMOVE FRONT DISC BRAKE CALIPER ASSEMBLY LH

  1. C102283E01
    Remove the 2 bolts, and disconnect the brake caliper assembly.

    NOTICE:
    Use a wire or an equivalent to keep the brake caliper from hanging down by the flexible hose.


45. REMOVE FRONT DISC BRAKE CALIPER ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


46. DISCONNECT FRONT SUSPENSION ARM SUB-ASSEMBLY UPPER LH

  1. C101998E01
    Remove the cotter pin and loosen the nut.
    SST
    09628-62011  

    NOTICE:
    Do not remove the nut.

  1. Using SST, separate the steering knuckle from the suspension upper arm and remove the nut.

    NOTICE:
    1. Fix the steering knuckle with a wire so that the flexible hose does not receive excessive force.
    2. Do not damage the ball joint dust cover.


47. DISCONNECT FRONT SUSPENSION ARM SUB-ASSEMBLY UPPER RH

HINT:
Use the same procedures described for the LH side.


48. DISCONNECT SHOCK ABSORBER ASSEMBLY FRONT LH

  1. C102009E02
    Remove the bolt and separate the front shock absorber from the front suspension lower arm.


49. DISCONNECT SHOCK ABSORBER ASSEMBLY FRONT RH

HINT:
Use the same procedures described for the LH side.


50. DISCONNECT STEERING TORQUE SHAFT ASSEMBLY

  1. C106142E01
    Loosen bolt (A) and remove bolt (B), then slide the steering torque shaft assembly.

    HINT:
    1. Do not remove bolt (A).
    2. Do not disconnect the steering torque shaft assembly from the power steering link assembly.

  1. C106143E01
    Put matchmarks on the steering torque shaft assembly and the power steering link assembly.

  1. Separate the steering torque shaft assembly from the power steering link assembly.


51. REMOVE ENGINE ASSEMBLY
  1. Set an engine lifter in place.

  1. A101144E02
    Remove the 16 bolts as shown in the illustration.

  1. Operate the engine lifter and slowly remove the engine from the vehicle.


52. INSTALL ENGINE HANGERS

  1. A239319E01
    Install 2 engine hangers with 2 bolts as shown in the illustration.

    HINT:
    Part No.
    No. 1 Engine Hanger
    12284-30020
    No. 2 Engine Hanger
    12282-67020
    Bolt
    91552-81014 and 91642-81030

    Torque:
    for No. 1 engine hanger:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    for No. 2 engine hanger:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

    NOTICE:
    Install the engine hangers with new bolts.


53. DISCONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE

  1. C101370E01
    Remove the clip and separate the No.1 oil reservoir to pump hose.


54. DISCONNECT PRESSURE FEED TUBE ASSEMBLY

  1. C101371E01
    Remove the union bolt and separate the pressure feed tube assembly.


55. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
  1. Hold the engine with an engine sling device and chain block.

  1. Remove the 4 bolts and front suspension crossmember.

  1. Remove the engine by operating the engine sling device and chain block.


56. REMOVE FRONT ENGINE MOUNTING INSULATOR
  1. Remove the 2 nuts, 2 engine mounting stabilizers and 2 front engine mounting insulators.


57. INSTALL ENGINE TO ENGINE STAND

58. REMOVE ENGINE WIRE
  1. Remove the engine wire from the engine.


59. REMOVE VANE PUMP ASSEMBLY

  1. C101372E01
    Remove the 2 nuts and the vane pump assembly.

  1. Remove the vane pump O-ring from the vane pump assembly.


60. REMOVE TIMING GEAR COVER INSULATOR

  1. A148171
    Remove the bolt and timing gear cover insulator.


61. REMOVE VACUUM PUMP ASSEMBLY

  1. A102102
    Remove the 2 nuts, vacuum pump and 2 O-rings.


62. REMOVE TIMING BELT
(Click here)

63. REMOVE ENGINE COOLANT TEMPERATURE SENSOR

  1. A239516E01
    Using SST, remove the engine coolant temperature sensor and gasket.
    SST
    09817-33190  


64. REMOVE CRANKSHAFT POSITION SENSOR

A102284
  1. Disconnect the crankshaft position sensor connector.

  1. Separate the connector from the No. 1 vacuum pipe .

  1. A151576
    Separate the 3 wire harness clamps.

  1. Remove the bolt and the crankshaft position sensor.


65. REMOVE CAMSHAFT POSITION SENSOR

A102283
  1. Disconnect the camshaft position sensor connector.

  1. Remove the bolt and the camshaft position sensor.


66. REMOVE DIESEL THROTTLE BODY ASSEMBLY

  1. w/o DPF:

    1. A177101
      Disconnect the diesel turbo pressure sensor connector and vacuum switching valve connector.

    2. Remove the bolt and disconnect the wire harness clamp.

  1. Disconnect the 2 diesel throttle body connectors.

  1. A257142E01
    Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.


67. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
(Click here)

68. REMOVE EGR COOLER ASSEMBLY
(Click here)

69. REMOVE VACUUM SWITCHING VALVE BRACKET

  1. A177110
    Disconnect the vacuum switching valve connector and 2 vacuum hoses.

  1. Remove the bolt and vacuum switching valve bracket.


70. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

  1. A177111
    Disconnect the 3 fuel hoses.

  1. A177112E01
    Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.


71. REMOVE COMMON RAIL ASSEMBLY
(Click here)

72. REMOVE FUEL SUPPLY PUMP ASSEMBLY
(Click here)

73. REMOVE CRANKSHAFT PULLEY

  1. A142434E01
    Using SST, remove the pulley bolt.
    SST
    09213-58014  
    09330-00021  

  1. A142416E01
    Using SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply oil or grease to the threads and tip of SST (center bolt) before using it.


74. REMOVE NO. 2 WATER BY-PASS PIPE
  1. Remove the bolt, 2 nuts and No. 2 water by-pass pipe.

  1. Remove the gasket.


75. REMOVE WATER INLET

  1. A263722
    Remove the 3 bolts and water inlet.


76. REMOVE THERMOSTAT
  1. Remove thermostat and gasket.


77. REMOVE NO. 2 CYLINDER BLOCK INSULATOR

78. REMOVE GLOW PLUG ASSEMBLY
(Click here)

79. REMOVE MANIFOLD STAY

  1. A262840E01
    Remove the 2 bolts and manifold stay.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF


80. REMOVE INTAKE MANIFOLD

  1. A172284
    Remove the 4 bolts, 2 nuts and intake manifold.

  1. Remove the gasket.


81. REMOVE WATER OUTLET
  1. Remove the 2 bolts, water outlet and gasket.


82. REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
  1. Disconnect the vacuum hose.

  1. Remove the bolt, nut and No. 1 vacuum transmitting pipe.


83. REMOVE NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
  1. Remove the bolt, 2 nuts and No. 2 vacuum transmitting pipe.


84. REMOVE OIL COOLER COVER SUB-ASSEMBLY
(Click here)

85. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

  1. A242796
    Remove the 4 bolts and front No. 1 engine mounting bracket.


86. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

  1. A242797
    Remove the 4 bolts and front No. 1 engine mounting bracket.

← REMOVAL (Oct 2014 – Nov 2017)INSTALLATION (Oct 2014 – Nov 2017) →