Rough Idling or Excessive Engine Vibrations
Circuit diagnosis · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
| Malfunction Condition |
Main Trouble Area |
Related Trouble Area |
|
|
|
- HINT:
- This troubleshooting procedure checks for the cause of rough idling and excessive engine vibrations.
- Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List result values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.
- Check that the vehicle has not been modified in any way prior to the vehicle inspection.
- This troubleshooting procedure checks for the cause of rough idling and excessive engine vibrations.
| Faults and Symptoms of Common Rail Diesel Components |
Engine Control
Glow System Main fault
Open circuit, glow plug relay fault
Symptoms
Difficult to start, rough idle, knocking, white smoke (when cold)
Data List
Check the glow plug indicator light
Diagnostic Point
Measure the resistance of the glow plug
Engine Main fault
Loss of compression
Symptoms
Rough idle (lack of power always)
Data List
Injection Feedback Val - When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.
- When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.
Diesel Injection
Fuel supply pump Main fault
-
Symptoms
Difficult to start, engine stalling, rough idle, lack of power
Data List
Common Rail Pressure, Target Common Rail Pressure - Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).
- If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.
- If the fuel pressure is below 25000 kPa, then idling will be rough.
- HINT:
- The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.
Diagnostic Trouble Code
Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.
Fuel filter Main fault
Blockage
Symptoms
Difficult to start, engine stalling, rough idle, lack of power
Data List
Common Rail Pressure, Target Common Rail Pressure - Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).
- If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.
- If the fuel pressure is below 25000 kPa, then idling will be rough.
- HINT:
- The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.
Diagnostic Trouble Code
Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.
Injector Assembly Main fault
Blockage
Symptoms
Rough idle, lack of power, black smoke, white smoke, knocking
Data List
Injection Feedback Val - When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.
Injector Driver Main fault
Circuit fault: The fuel injector assembly does not open.
Symptoms
Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
Data List
Same as injector assembly
Diagnostic Trouble Code
When the injector driver has a fault, some DTCs may be stored.
Fuel Pressure Sensor Main fault
Open circuit, decrease in performance (foreign matter is stuck)
Symptoms
Difficult to start, rough idle, engine stall, lack of power
Data List
Common Rail Pressure, Target Common Rail Pressure - Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped, and check that Common Rail Pressure follows Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure. (However, the value may not deviate even when a malfunction is present).
Diagnostic Trouble Code
When the fuel pressure sensor has a fault, some DTCs may be stored.
Irregular Fuel Main fault
-
Symptoms
Difficult to start, rough idle (especially when cold)
- Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).
Diesel EGR
EGR System Main fault
- Does not move smoothly
- Does not close completely
Symptoms
- Rough idle
- EGR valve stuck closed: A loud turbocharger sound.
- EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).
- Does not move smoothly
Diesel Throttle
Diesel Throttle System Main fault
Stuck, does not move smoothly
Symptoms
- Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
- Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.
- Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
| Data List Related to Lack of Power |
- Engine Speed
- Intake Air
- Coolant Temp
- Target Common Rail Pressure
- Common Rail Pressure
- Injection Feedback Val #1 (to #4)
- Injection Volume
INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
| 1. CHECK MALFUNCTION CONDITION |
Identify when shuddering occurs.
Result Result
Proceed to
When idling
A
When engaging engine clutch at vehicle start
B
(Clutch system shudders)
|
|
||||
| A | |
| 2. CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT |
Check the wire harness and connector connections of common rail system components.
- OK:
- The wire harnesses and connectors are connected securely.
- HINT:
- The engine may have problems when there is an intermittent disconnection in a circuit related to the fuel pressure sensor, crankshaft position sensor, engine coolant temperature sensor, etc.
|
|
||||
| OK | |
| 3. READ OUTPUT DTC (RELATING TO ENGINE) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read pending DTCs.
| Result |
Proceed to |
| No DTCs are output |
A |
| Engine related DTCs are output |
B |
|
|
||||
| A | |
| 4. TAKE SNAPSHOT DURING IDLING (PROCEDURE 4) |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).
Enter the following menus: Powertrain / Engine and ECT / Data List.
Take a snapshot when idling with no load after the engine is warmed up and when the problem is occurring.
- HINT:
- A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
- The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
- If rough idling occurs when the A/C switch is on, take another snapshot with the A/C switch on.
- Take a snapshot when the problem is occurring, such as when the engine is cold. However, if the problem does not reoccur, it is acceptable to only take a snapshot after the engine is warmed up.
- A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
| NEXT | |
| 5. CHECK WHITE SMOKE |
Start the engine.
Fully depress the accelerator pedal, and then release it.
Check whether white smoke is emitted when racing the engine.
- NOTICE:
- Be sure not to check for white smoke indoors.
- HINT:
- Depending on whether there is oil mixed with the fuel, or whether there is unburned fuel present, the smell of the exhaust gas differs. When oil is mixed in, the exhaust gas smells like burning oil.
Result Result
Proceed to
White smoke is not emitted
A
White smoke is emitted
B
|
|
||||
| A | |
| 6. CHECK DATA LIST (ENGINE SPEED) |
Check engine speed in the snapshot taken in procedure 4 when the engine was idling.
Result Result
Proceed to
Change in engine speed coincides with air conditioning system operation
B
Except above
A
|
|
||||
| A | |
| 7. CHECK DATA LIST (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME) |
Check Injection Feedback Val # in the snapshot taken in procedure 4 when the engine was idling.
Result Result
Proceed to
Injection Feedback Val for at least one cylinder is more than +3 mm3/st and engine vibration is abnormally large
A
Except above
B
- HINT:
- When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
- The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st, as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.
- When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
|
|
||||
| A | |
| 8. INSPECT INJECTOR COMPENSATION CODE |
Read the injector compensation code (Click here).
- OK:
- Compensation codes stored in the ECM match compensation codes of the installed injector assemblies.
|
|
||||
| OK | |
| 9. PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT) |
- HINT:
- Use this Active Test to determine the malfunctioning cylinder.
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut.
- HINT:
- If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning.
- If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.
- If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning.
| NEXT | |
| 10. REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER |
Replace the injector assembly of the malfunctioning cylinder (Click here).
- NOTICE:
- When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
- Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
- If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
- If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
- If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
- When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
| NEXT | |
| 11. CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER |
Clean the fuel filter case and replace the fuel filter.
- HINT:
- Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.
| NEXT | |
| 12. BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system (Click here).
| NEXT | |
| 13. PERFORM ECM INITIALIZATION AND REGISTER INJECTOR COMPENSATION CODE |
Perform the ECM initialization.
Connect terminals 13 (TC) and 4 (CG) of the DLC3.

Turn the ignition switch to ON for 50 minutes or more.
- NOTICE:
- Perform ECM initialization only when the injectors for all the cylinders have been replaced.
- It is necessary to wait for 50 minutes or more. Otherwise, ECM initialization is not completed.
- Perform ECM initialization only when the injectors for all the cylinders have been replaced.
Turn the ignition switch off.
Disconnect terminals 13 (TC) and 4 (CG).
Register the injector compensation code (Click here).
|
|
||||
| 14. REPAIR OR REPLACE HARNESS AND CONNECTOR |
Repair or replace the harness or connector.
|
|
||||
| 15. CHECK AND REPAIR ENGINE ASSEMBLY |
Check the following items and repair the malfunctioning part if necessary.
Check cylinder compression pressure (Click here).
|
|
||||
| 16. CHECK AIR CONDITIONING SYSTEM |
Check the air conditioning system.
- HINT:
- Be sure to check the air conditioning hoses and pipes.
- Check the refrigerant pressure (Click here).
- Be sure to check the air conditioning hoses and pipes.
|
|
||||
| 17. CHECK DATA LIST (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE) |
Check engine speed in the snapshot taken in procedure 4 when the engine was idling after having been warmed up.
Result Result
Proceed to
Common Rail Pressure is more than 5000 kPa from Target Common Rail Pressure
A
Except above
B
|
|
||||
| A | |
| 18. CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail.
With no load after the engine is warmed up, take a snapshot when idling and vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.
Check the Target Common Rail Pressure and Common Rail Pressure value.


Result Result
Proceed to
While idling the vehicle, "Common Rail Pressure" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1
A
"Common Rail Pressure" is normal while idling the vehicle, but "Common Rail Pressure" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear*2
Except above
B
- NOTICE:
- *1: The cause may be a squashed or blocked fuel pipe or hose.
- *2: The cause may be a clogged fuel filter.
- *1: The cause may be a squashed or blocked fuel pipe or hose.
|
|
||||
| B | |
| 19. REPLACE SUCTION CONTROL VALVE |
Replace the suction control valve (Click here).
| NEXT | |
| 20. BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system (Click here).
| NEXT | |
| 21. PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
|
|
||||
| 22. REPAIR OR REPLACE CLOGGED FUEL LINE |
Repair or replace the clogged (including frozen fuel) fuel pipe.
Replace the fuel filter element sub-assembly.
- HINT:
- If "Common Rail Pressure" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel filter element sub-assembly.
| NEXT | |
| 23. BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system (Click here).
|
|
||||
| 24. REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY) |
Remove the electric EGR control valve assembly (Click here).
Visually check the electric EGR control valve assembly for deposits.If there are deposits, clean the electric EGR control valve assembly.
- HINT:
- If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.
- If the EGR valve does not operate due to clogging or disconnection of the vacuum hose, repair the hose.
- If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power. In this case, clean the electric EGR control valve assembly.
- When cleaning the electric vacuum regulating valve assembly, use a piece of cloth soaked with non-residue solvent. Spraying the solvent directly onto these parts or soaking the parts in solvent may damage the parts.
- If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.
Reinstall the electric EGR control valve assembly (Click here).
| NEXT | |
| 25. CHECK AND REPLACE ENGINE MOUNTING INSULATOR |
Check the following items and repair or replace the malfunctioning part if necessary.
Check that the engine mounting insulators are installed correctly.
Check that the engine mounting insulators are not twisted.
Check that deformation of an engine mounting insulator is not causing the engine to contact the vehicle body.
| NEXT | |
| 26. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
