2014-2019 Hiace · Service Manual BRAKE

C1405 Open or Short in Front Speed Sensor RH Circuit

Diagnostic trouble codes · Vehicles built Jan 2017 – Nov 2017

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

Refer to DTCs C1401 and C1402 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
C1405
C1406
Either of the following is detected:
  1. An open in the speed sensor signal circuit continues for 0.5 seconds or more.
  2. With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.
  1. Front speed sensor RH/LH
  2. Skid control ECU (Brake actuator assembly)
  3. Wire harness or connector

HINT:
  1. DTC C1405 is for the front speed sensor RH.
  2. DTC C1406 is for the front speed sensor LH.


WIRING DIAGRAM

Refer to DTCs C1401 and C1402 (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    Front speed sensor RH open detection / Error or Normal
    Normal
    Error: Momentary interruption
    FL Speed Open
    Front speed sensor LH open detection / Error or Normal
    Normal
    Error: Momentary interruption

    OK:
    Normal (There are no momentary interruptions.)

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 4
OK


2. READ VALUE USING GTS (FRONT SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    FL Wheel Speed
    Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
Go to step 4
OK


3. RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Perform a road test.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTCs C1405 and C1406 are not output
    A
    DTCs C1405 and/or C1406 are output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

4. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Disconnect the B18 or B20 front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    B92-31 (FR+) - B18-2
    Always
    Below 1 Ω
    B92-31 (FR+) or B18-2 - Body ground
    Always
    10 kΩ or higher
    B92-30 (FR-) - B18-1
    Always
    Below 1 Ω
    B92-30 (FR-) or B18-1 - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    B92-18 (FL+) - B20-2
    Always
    Below 1 Ω
    B92-18 (FL+) or B20-2 - Body ground
    Always
    10 kΩ or higher
    B92-17 (FL-) - B20-1
    Always
    Below 1 Ω
    B92-17 (FL-) or B20-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

  1. C321141E01
    Reconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    B18-2 - Body ground
    Ignition switch ON
    8 to 14 V
    for LH:
    Tester Connection
    Condition
    Specified Condition
    B20-2 - Body ground
    Ignition switch ON
    8 to 14 V

    Text in Illustration 
    *A
    for RH
    *B
    for LH
    *a
    Front view of wire harness connector
    (to Front Speed Sensor)

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

REPLACE FRONT SPEED SENSOR (Click here)


← C1405 Open or Short in Front Speed Sensor RH Circuit (+ C1406) (Apr 2016 – Dec 2016)C1405 Open or Short in Front Speed Sensor RH Circuit (+ C1406) (from Dec 2017) →