2014-2019 Hiace · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Jan 2015

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015

HINT:
w/ Dual VVT-i:
Perform "Inspection After Repair" after replacing an ignition coil assembly or spark plug (Click here).


PERFORM SPARK TEST
  1. Check for DTCs.

    1. w/ Dual VVT-i (Click here)
    2. w/ Secondary Air Injection System (Click here)
    3. w/o Secondary Air Injection System (Click here)

    NOTICE:
    If a DTC is present, perform troubleshooting procedures for that DTC.

  1. Check if sparks occur.

    1. Remove the front seat assembly.

      1. for Hi-back Seat Type (Click here)
      2. for Low-back Seat Type (Click here)
      3. for Split Bench Seat Type (Click here)
      4. for Center Seat Type (Click here)

    2. Remove the front door scuff plate RH.

    3. Remove the 5 bolts and the engine service hole sub cover.

    4. Remove the ignition coil assembly.

    5. Using 16 mm plug wrench, remove the spark plug.

    6. Install the spark plug to the ignition coil assembly and connect the ignition coil connector.

    7. Disconnect the 4 injector connectors.

    8. Ground the spark plug.

    9. Visually check that sparks occur while the engine is being cranked.

      NOTICE:
      1. Be sure to ground the spark plug before checking.
      2. If the ignition coil has been struck or dropped, replace it.
      3. Do not crank the engine for more than 2 seconds.


INSPECT IGNITION COIL AND SPARK TEST
  1. Spark test flowchart.

    HINT:
    w/ Dual VVT-i:
    Perform "Inspection After Repair" after replacing an ignition coil assembly or spark plug (Click here).


    1. Check that the wire harness side connector of the ignition coil assembly with igniter is securely connected.

      Result:
      Result
      Proceed to
      NG
      Connect securely
      OK
      Go to next step

    2. Perform spark test on each ignition coil assembly with igniter.

      1. Replace the ignition coil assembly with igniter with a normal one.
      2. Perform spark test again.

      Result:
      Result
      Proceed to
      OK
      Replace ignition coil assembly with igniter
      NG
      Go to next step

    3. Check the spark plug.

      Result:
      Result
      Proceed to
      NG
      Replace spark plug
      OK
      Go to next step

    4. Check the power supply to ignition coil assembly with igniter.

      1. Turn the ignition switch to ON.
      2. Check that there is battery voltage at the ignition coil positive (+) terminal.

      Result (w/ Dual VVT-i):
      Result
      Proceed to
      NG
      Check wiring between engine switch and ignition coil assembly with igniter
      OK
      Go to check crankshaft position sensor

      Result (w/o Dual VVT-i):
      Result
      Proceed to
      NG
      Check wiring between engine switch and ignition coil assembly with igniter
      OK
      Go to next step

    5. w/o Dual VVT-i:
      Check the camshaft position sensor (Click here).

      Result:
      Result
      Proceed to
      NG
      Replace camshaft position sensor
      OK
      Go to next step

    6. Check the crankshaft position sensor (Click here).

      Result:
      Result
      Proceed to
      NG
      Replace crankshaft position sensor
      OK
      Go to next step

    7. Check IGT signal from the ECM.

      Result:
      Result
      Proceed to
      NG
      Check ECM
      OK
      Repair wiring between ignition coil and ECM

  1. Install the ignition coil assembly.

    1. Using a 16 mm plug wrench, install the spark plug.

      Torque:
      18 N*m{ 183 kgf*cm , 13 ft.*lbf }

    2. Install the ignition coil assembly.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    3. Install the engine service hole sub cover with the 5 bolts.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    4. Install the front door scuff plate RH.

    5. Install the front seat assembly.

      1. for Hi-back Seat Type (Click here)
      2. for Low-back Seat Type (Click here)
      3. for Split Bench Seat Type (Click here)
      4. for Center Seat Type (Click here)


CHECK SPARK PLUG

NOTICE:
  1. Do not use a wire brush for cleaning.
  2. Do not attempt to adjust the electrode gap of a used spark plug.

HINT:
w/ Dual VVT-i:
Perform "Inspection After Repair" after replacing an spark plug (Click here).

  1. A120009E03
    Check the electrode.

    1. Using a megohmmeter, measure the insulation resistance.

      Standard Insulator Resistance:
      Tester Connection
      Condition
      Specified Condition
      Spark plug (terminal part) - Body ground
      part) - Body ground
      10 MΩ or more

      Text in Illustration 
      *a
      Body Ground

      HINT:
      If a megohmmeter is not available, perform the following simple inspection instead.

  1. Alternative inspection method.

    1. Quickly accelerate the engine to 4000 rpm 5 times.

    2. Remove the spark plug.

    3. Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage to its threads and insulator.
    If there is damage, replace the spark plug. If not, reinstall the spark plug.

    Recommended spark plug (w/ Dual VVT-i):
    Manufacture
    Product
    DENSO made
    FK20HR-A8

    Recommended spark plug (w/o Dual VVT-i):
    Manufacture
    Product
    DENSO made
    SK20HR-A11

  1. w/ Dual VVT-i:
    Check the spark plug electrode gap.

    Maximum electrode gap for used spark plug:
    1.1 mm (0.0433 in.)

    If the gap is greater than the maximum, replace the spark plug.

    Electrode gap for new spark plug:
    0.7 to 0.8 mm (0.0276 to 0.0315 in.)

    NOTICE:
    When adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap of a used plug.

  1. w/o Dual VVT-i:
    Check the spark plug electrode gap.

    Maximum electrode gap for used spark plug:
    1.3 mm (0.0512 in.)

    If the gap is greater than the maximum, replace the spark plug.

    Electrode gap for new spark plug:
    1.0 to 1.1 mm (0.0394 to 0.0433 in.)

    NOTICE:
    When adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap of a used plug.

  1. B062019E01
    Clean the spark plugs.
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Air pressure:
    588 kPa (6.0 kgf/cm2, 85 psi)

    Duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.

← ON-VEHICLE INSPECTION (Oct 2014 – Dec 2014)PRECAUTION (from Oct 2014) →