2014-2019 Hiace · Service Manual ENGINE

P0135 Oxygen Sensor Heater Circuit (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built from Jan 2015

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015

DESCRIPTION

Refer to DTC P0130 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P0135
Open or short in the heater circuit of the oxygen sensor for 0.5 seconds or more (1 trip detection logic).
  1. Open or short in heater circuit of oxygen sensor
  2. Heated oxygen sensor
  3. ECM

WIRING DIAGRAM

Refer to DTC P0130 (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
  1. Inspect the heated oxygen sensor (Click here).



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


2. CHECK TERMINAL VOLTAGE (+B OF HEATED OXYGEN SENSOR)
A208632E12
  1. Disconnect the heated oxygen sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D34-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Heated Oxygen Sensor)



NG
Go to step 5
OK


3. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
  1. Disconnect the heated oxygen sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D34-1 (HT1A) - D97-104 (HA1A)
    Always
    Below 1 Ω
    D34-1 (HT1A) or D97-104 (HA1A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Wait 5 seconds or more.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTC P0135 is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

5. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
  1. Disconnect the heated oxygen sensor connector.

  1. Remove the No. 1 integration relay from the No. 1 engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D34-2 (+B) - 10A-8
    Always
    Below 1 Ω
    D34-2 (+B) or 10A-8 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)


← P0135 Oxygen Sensor Heater Circuit (Bank 1 Sensor 1) (Oct 2014 – Dec 2014)P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) (+ P0328) (Oct 2014 – Dec 2014) →