2014-2019 Hiace · Service Manual BODY ELECTRICAL

Illumination Circuit

Circuit diagnosis · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch LH illumination when the headlight dimmer switch assembly is in the tail or head position.

WIRING DIAGRAM

E291243E01

INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (Click here).


1. CHECK ILLUMINATION
  1. Check if the illumination for the radio receiver assembly, steering pad switch LH, glove box or other parts (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the tail or head position.

    Result 
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch LH
    A
    Illumination comes on for all components except radio receiver assembly.
    B
    No illumination comes on (radio receiver assembly, hazard switch, glove box, etc.).
    C



B
Go to step 6

C
GO TO LIGHTING SYSTEM (Click here)
A


2. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY)

  1. E291244E01
    Disconnect the spiral cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H77-13 (IL2+) - Body ground
    Headlight dimmer switch assembly tail or head
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Spiral Cable Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT STEERING PAD SWITCH LH
  1. Remove the steering pad switch LH (Click here).

  1. Inspect the steering pad switch LH (Click here).



NG
REPLACE STEERING PAD SWITCH LH (Click here)
OK


4. INSPECT SPIRAL CABLE SUB-ASSEMBLY
  1. Remove the spiral cable sub-assembly (Click here).

  1. Inspect the spiral cable sub-assembly (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)
  1. Disconnect the I2 radio receiver assembly connector.

  1. Disconnect the H77 spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I2-9 (SWG) - H77-3 (EAU)
    Always
    Below 1 Ω
    I2-9 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

6. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

  1. E277492E79
    Disconnect the radio receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I2-7 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I2-10 (ILL+) - Body ground
    Headlight dimmer switch assembly tail or head
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio Receiver Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Illumination Circuit (Apr 2016 – Dec 2016)Speaker Circuit (Oct 2014 – Mar 2016) →