HOW TO PROCEED WITH TROUBLESHOOTING
Troubleshooting · Vehicles built Dec 2015 – Mar 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
- HINT:
- Use this procedure to troubleshoot the immobiliser system.
- *: Use the GTS.
- Use this procedure to troubleshoot the immobiliser system.
| 1.VEHICLE BROUGHT TO WORKSHOP |
| |||||
| 2.CUSTOMER PROBLEM ANALYSIS |
- HINT:
- In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
- Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
- The following 5 items are important points for problem analysis:
- In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
| What |
Vehicle model, system name |
| When |
Date, time, occurrence frequency |
| Where |
Whether the problem occurs at a specific location. |
| Under what conditions? |
Whether the doors were locked or unlocked, whether the ignition switch was ON, whether the engine was running. |
| How did it happen? |
Problem symptoms |
| |||||
| 3.INSPECT BATTERY VOLTAGE |
Measure the battery voltage.
- Standard voltage:
- 11 to 14 V
| |||||
| 4.CRANK ENGINE FOR MORE THAN 10 SECONDS |
| |||||
| 5.CHECK FOR DTC* (ECM) |
Check for DTCs and note any codes that are output.
- HINT:
- Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.
Result Result
Proceed to
DTCs are not output
A
SFI system DTCs are output (for 1TR-FE [w/ Dual VVT-i])
B
SFI system DTCs are output (for 2TR-FE [w/ Secondary Air Injection System])
C
SFI system DTCs are output (for 2TR-FE [w/o Secondary Air Injection System])
D
SFI system DTCs are output (for 2TR-FE [w/ Dual VVT-i])
E
ECD system DTCs are output (for 1KD-FTV [w/o DPF])
F
ECD system DTCs are output (for 1KD-FTV [w/ DPF])
G
ECD system DTCs are output (for 2KD-FTV)
H
Immobiliser system DTCs are output
I
|
|||||
|
|||||
|
|||||
|
|||||
|
|||||
|
|||||
|
|||||
|
|||||
| |||||
| 6.CHECK FOR DTC* (TRANSPONDER KEY ECU ASSEMBLY) |
Check for DTCs and note any codes that are output (Click here).
- HINT:
- Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.
Result Result
Proceed to
DTCs are not output
A
Immobiliser system DTCs are output
B
|
|||||
| |||||
| 7.PROBLEM SYMPTOMS TABLE |
Refer to Problem Symptoms Table (Click here).
Result Result
Proceed to
Fault is not listed in problem symptoms table
A
Fault is listed in problem symptoms table
B
|
|||||
| |||||
| 8.OVERALL ANALYSIS AND TROUBLESHOOTING* |
Data List / Active Test (Click here).
Terminals of ECU (Click here).
| |||||
| 9.REPAIR OR REPLACE |
- HINT:
- If the transponder key ECU assembly, ECM, or key are replaced, refer to Service Bulletin.
| |||||
| 10.CHECK FOR DTC* |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- HINT:
- Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.
Result Result
Proceed to
DTCs are not output
A
Immobiliser system DTCs are output
B
|
|||||
| |||||