B2799 Engine Immobiliser System Malfunction
Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 from Apr 2016
DESCRIPTION
The ECM stores this DTC when the communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.| DTC No. |
DTC Detection Condition |
Trouble Area |
DTC Output Confirmation Operation |
| B2799 |
One of the following conditions is met:
|
|
|
| Vehicle Condition when Malfunction Detected |
Fail-safe Operation when Malfunction Detected |
| Engine cannot be started |
- |
| DTC No. |
Data List and Active Test |
| B2799 |
- |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.
- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
- When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.
- HINT:
- If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Start the engine.
Check for DTCs (Click here).
- HINT:
- Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
- OK:
- DTC B2799 is not output.
Result Result
Proceed to
OK
A
NG (DTC B2799 is output)
B
NG (Other DTCs are output)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 3. REGISTER ECU COMMUNICATION ID |
Reregister the ECU communication ID.
- HINT:
- Refer to Service Bulletin.
| NEXT | |
| 4. CHECK WHETHER ENGINE STARTS |
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
- OK:
- Engine starts normally.
|
|
||||
| OK | ||
| ||
| 5. REPLACE ECM |
Temporarily replace the ECM with a new one or known good one.
- for 1TR-FE: Click here
- for 2TR-FE: Click here
- for 1KD-FTV: Click here
- for 2KD-FTV: Click here
- for 1TR-FE: Click here
| NEXT | |
| 6. CHECK WHETHER ENGINE STARTS |
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
- OK:
- Engine starts normally.
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM) |
- *1: for 1TR-FE, 2TR-FE
- *2: for 1KD-FTV (w/o DPF)
- *3: for 1KD-FTV (w/ DPF)
- *4: for 2KD-FTV
Disconnect the H60 transponder key ECU assembly connector.
Disconnect the B71*1, B72*2, B73*3 or B88*4 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for 1TR-FE, 2TR-FE:
Tester Connection
Condition
Specified Condition
H60-12 (EFII) - B71-10 (IMO)
Always
Below 1 Ω
H60-13 (EFIO) - B71-11 (IMI)
Always
Below 1 Ω
H60-12 (EFII) - Body ground
Always
10 kΩ or higher
H60-13 (EFIO) - Body ground
Always
10 kΩ or higher
B71-10 (IMO) - Body ground
Always
10 kΩ or higher
B71-11 (IMI) - Body ground
Always
10 kΩ or higher
- for 1KD-FTV (w/o DPF):
Tester Connection
Condition
Specified Condition
H60-12 (EFII) - B72-15 (IMO)
Always
Below 1 Ω
H60-13 (EFIO) - B72-16 (IMI)
Always
Below 1 Ω
H60-12 (EFII) - Body ground
Always
10 kΩ or higher
H60-13 (EFIO) - Body ground
Always
10 kΩ or higher
B72-15 (IMO) - Body ground
Always
10 kΩ or higher
B72-16 (IMI) - Body ground
Always
10 kΩ or higher
- for 1KD-FTV (w/ DPF):
Tester Connection
Condition
Specified Condition
H60-12 (EFII) - B73-15 (IMO)
Always
Below 1 Ω
H60-13 (EFIO) - B73-16 (IMI)
Always
Below 1 Ω
H60-12 (EFII) - Body ground
Always
10 kΩ or higher
H60-13 (EFIO) - Body ground
Always
10 kΩ or higher
B73-15 (IMO) - Body ground
Always
10 kΩ or higher
B73-16 (IMI) - Body ground
Always
10 kΩ or higher
- for 2KD-FTV:
Tester Connection
Condition
Specified Condition
H60-12 (EFII) - B88-15 (IMO)
Always
Below 1 Ω
H60-13 (EFIO) - B88-16 (IMI)
Always
Below 1 Ω
H60-12 (EFII) - Body ground
Always
10 kΩ or higher
H60-13 (EFIO) - Body ground
Always
10 kΩ or higher
B88-15 (IMO) - Body ground
Always
10 kΩ or higher
B88-16 (IMI) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
