2014-2019 Hiace · Service Manual SECURITIES

B2799 Engine Immobiliser System Malfunction

Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 from Apr 2016

DESCRIPTION

The ECM stores this DTC when the communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.
DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2799
One of the following conditions is met:
  1. Error in communication between ECM and transponder key ECU assembly.
  2. Error in communication lines.
  3. Communication ID is different during communication between ECM and transponder key ECU assembly.
  1. Wire harness or connector
  2. Transponder key ECU
  3. ECM
  1. Start the engine and wait 10 seconds.*1
  2. After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.*2
    *1: Communication starts within 3 seconds of starting the engine. If verification fails, this DTC is stored 6 seconds after communication has completed.
    *2: Communication starts within 3 seconds of turning the ignition switch to ON. If verification fails, this DTC is stored 6 seconds after communication has completed.
Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started
-
Related Data List and Active Test 
DTC No.
Data List and Active Test
B2799
-

WIRING DIAGRAM

B365295E06

INSPECTION PROCEDURE

NOTICE:
  1. If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.
  2. After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
  3. When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

HINT:
If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Start the engine.

  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2799 is not output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (DTC B2799 is output)
    B
    NG (Other DTCs are output)
    C



B
Go to step 3

C
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

3. REGISTER ECU COMMUNICATION ID
  1. Reregister the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


4. CHECK WHETHER ENGINE STARTS
  1. Using a registered key, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

    OK:
    Engine starts normally.



NG
Go to step 5
OK

END (ECU COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

5. REPLACE ECM
  1. Temporarily replace the ECM with a new one or known good one.

    1. for 1TR-FE: Click here
    2. for 2TR-FE (w/o Dual VVT-i): Click here
    3. for 2TR-FE (w/ Dual VVT-i): Click here
    4. for 1KD-FTV: Click here
    5. for 2KD-FTV: Click here


NEXT


6. CHECK WHETHER ENGINE STARTS
  1. Using a registered key, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

    OK:
    Engine starts normally.



NG
Go to step 7
OK

END (ECM WAS DEFECTIVE)

7. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
  1. *1: for 2TR-FE (w/o Dual VVT-i)
  2. *2: for 1KD-FTV (w/o DPF)
  3. *3: for 1KD-FTV (w/ DPF)
  4. *4: for 2KD-FTV
  5. *5: for 1TR-FE (w/ Dual VVT-i), 2TR-FE (w/ Dual VVT-i)
  1. Disconnect the H60 transponder key ECU assembly connector.

  1. Disconnect the B71*1, B72*2, B73*3, B88*4 or B94*5 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2TR-FE (w/o Dual VVT-i):
    Tester Connection
    Condition
    Specified Condition
    H60-12 (EFII) - B71-10 (IMO)
    Always
    Below 1 Ω
    H60-13 (EFIO) - B71-11 (IMI)
    Always
    Below 1 Ω
    H60-12 (EFII) - Body ground
    Always
    10 kΩ or higher
    H60-13 (EFIO) - Body ground
    Always
    10 kΩ or higher
    B71-10 (IMO) - Body ground
    Always
    10 kΩ or higher
    B71-11 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (w/o DPF):
    Tester Connection
    Condition
    Specified Condition
    H60-12 (EFII) - B72-15 (IMO)
    Always
    Below 1 Ω
    H60-13 (EFIO) - B72-16 (IMI)
    Always
    Below 1 Ω
    H60-12 (EFII) - Body ground
    Always
    10 kΩ or higher
    H60-13 (EFIO) - Body ground
    Always
    10 kΩ or higher
    B72-15 (IMO) - Body ground
    Always
    10 kΩ or higher
    B72-16 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (w/ DPF):
    Tester Connection
    Condition
    Specified Condition
    H60-12 (EFII) - B73-15 (IMO)
    Always
    Below 1 Ω
    H60-13 (EFIO) - B73-16 (IMI)
    Always
    Below 1 Ω
    H60-12 (EFII) - Body ground
    Always
    10 kΩ or higher
    H60-13 (EFIO) - Body ground
    Always
    10 kΩ or higher
    B73-15 (IMO) - Body ground
    Always
    10 kΩ or higher
    B73-16 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2KD-FTV:
    Tester Connection
    Condition
    Specified Condition
    H60-12 (EFII) - B88-15 (IMO)
    Always
    Below 1 Ω
    H60-13 (EFIO) - B88-16 (IMI)
    Always
    Below 1 Ω
    H60-12 (EFII) - Body ground
    Always
    10 kΩ or higher
    H60-13 (EFIO) - Body ground
    Always
    10 kΩ or higher
    B88-15 (IMO) - Body ground
    Always
    10 kΩ or higher
    B88-16 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 1TR-FE (w/ Dual VVT-i), 2TR-FE (w/ Dual VVT-i):
    Tester Connection
    Condition
    Specified Condition
    H60-12 (EFII) - B94-45 (IMO)
    Always
    Below 1 Ω
    H60-13 (EFIO) - B94-28 (IMI)
    Always
    Below 1 Ω
    H60-12 (EFII) - Body ground
    Always
    10 kΩ or higher
    H60-13 (EFIO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)


← B2799 Engine Immobiliser System Malfunction (Oct 2014 – Dec 2014)B2799 Engine Immobiliser System Malfunction (from Apr 2016) →