2014-2019 Hiace · Service Manual SECURITIES

B279A Theft Deterrent System Communication Line High Fixation

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.
DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B279A
Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
  1. Harness or connector
  2. ECM
  3. Transponder key ECU assembly
Turn the ignition switch to ON and wait 6 seconds.
Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops)
Engine cannot be started
Related Data List and Active Test 
DTC No.
Data List and Active Test
B279A
-

WIRING DIAGRAM

B365296E03

INSPECTION PROCEDURE

NOTICE:
  1. If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.
  2. After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
  3. When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B279A is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK CONNECTION OF CONNECTOR
  1. Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


4. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
  1. *1: for 1TR-FE, 2TR-FE
  2. *2: for 1KD-FTV (w/o DPF)
  3. *3: for 1KD-FTV (w/ DPF)
  4. *4: for 2KD-FTV
  1. Disconnect the H60 transponder key ECU assembly connector.

  1. Disconnect the B71*1, B72*2, B73*3 or B88*4 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1TR-FE, 2TR-FE:
    Tester Connection
    Condition
    Specified Condition
    H60-13 (EFIO) - B71-11 (IMI)
    Always
    Below 1 Ω
    H60-13 (EFIO) - Body ground
    Always
    10 kΩ or higher
    B71-11 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (w/o DPF):
    Tester Connection
    Condition
    Specified Condition
    H60-13 (EFIO) - B72-16 (IMI)
    Always
    Below 1 Ω
    H60-13 (EFIO) - Body ground
    Always
    10 kΩ or higher
    B72-16 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (w/ DPF):
    Tester Connection
    Condition
    Specified Condition
    H60-13 (EFIO) - B73-16 (IMI)
    Always
    Below 1 Ω
    H60-13 (EFIO) - Body ground
    Always
    10 kΩ or higher
    B73-16 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2KD-FTV:
    Tester Connection
    Condition
    Specified Condition
    H60-13 (EFIO) - B88-16 (IMI)
    Always
    Below 1 Ω
    H60-13 (EFIO) - Body ground
    Always
    10 kΩ or higher
    B88-16 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly with a new one.


NEXT


6. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7. CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B279A is not output.

    Result 
    Result
    Proceed to
    DTC B279A is not output
    A
    DTC B279A is output (for 1TR-FE)
    B
    DTC B279A is output (for 2TR-FE)
    C
    DTC B279A is output (for 1KD-FTV)
    D
    DTC B279A is output (for 2KD-FTV)
    E



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPLACE ECM (Click here)
A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)


← B2799 Engine Immobiliser System Malfunction (from Apr 2016)B279A Theft Deterrent System Communication Line High Fixation (Jan 2015 – Mar 2016) →