B279A Theft Deterrent System Communication Line High Fixation
Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.| DTC No. |
DTC Detection Condition |
Trouble Area |
DTC Output Confirmation Operation |
| B279A |
Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high. |
|
Turn the ignition switch to ON and wait 6 seconds. |
| Vehicle Condition when Malfunction Detected |
Fail-safe Operation when Malfunction Detected |
| Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) |
Engine cannot be started |
| DTC No. |
Data List and Active Test |
| B279A |
- |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.
- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
- When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
- HINT:
- Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
- OK:
- DTC B279A is not output.
|
|
||||
| OK | ||
| ||
| 3. CHECK CONNECTION OF CONNECTOR |
Check that the connectors are properly connected to the ECM and transponder key ECU assembly.
- OK:
- Connectors are properly connected.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM) |
- *1: for 2TR-FE (w/o Dual VVT-i)
- *2: for 1KD-FTV (w/o DPF)
- *3: for 1KD-FTV (w/ DPF)
- *4: for 2KD-FTV
- *5: for 1TR-FE (w/ Dual VVT-i), 2TR-FE (w/ Dual VVT-i)
Disconnect the H60 transponder key ECU assembly connector.
Disconnect the B71*1, B72*2, B73*3, B88*4 or B94*5 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for 2TR-FE (w/o Dual VVT-i):
Tester Connection
Condition
Specified Condition
H60-13 (EFIO) - B71-11 (IMI)
Always
Below 1 Ω
H60-13 (EFIO) - Body ground
Always
10 kΩ or higher
B71-11 (IMI) - Body ground
Always
10 kΩ or higher
- for 1KD-FTV (w/o DPF):
Tester Connection
Condition
Specified Condition
H60-13 (EFIO) - B72-16 (IMI)
Always
Below 1 Ω
H60-13 (EFIO) - Body ground
Always
10 kΩ or higher
B72-16 (IMI) - Body ground
Always
10 kΩ or higher
- for 1KD-FTV (w/ DPF):
Tester Connection
Condition
Specified Condition
H60-13 (EFIO) - B73-16 (IMI)
Always
Below 1 Ω
H60-13 (EFIO) - Body ground
Always
10 kΩ or higher
B73-16 (IMI) - Body ground
Always
10 kΩ or higher
- for 2KD-FTV:
Tester Connection
Condition
Specified Condition
H60-13 (EFIO) - B88-16 (IMI)
Always
Below 1 Ω
H60-13 (EFIO) - Body ground
Always
10 kΩ or higher
B88-16 (IMI) - Body ground
Always
10 kΩ or higher
- for 1TR-FE (w/ Dual VVT-i), 2TR-FE (w/ Dual VVT-i):
Tester Connection
Condition
Specified Condition
H60-13 (EFIO) - B94-28 (IMI)
Always
Below 1 Ω
H60-13 (EFIO) - Body ground
Always
10 kΩ or higher
B94-28 (IMI) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. REPLACE TRANSPONDER KEY ECU ASSEMBLY |
Replace the transponder key ECU assembly with a new one.
| NEXT | |
| 6. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 7. CHECK FOR DTC |
Check for DTCs (Click here).
- HINT:
- Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
- OK:
- DTC B279A is not output.
- *: Go to procedure:
- DTC B279A is output (for 1TR-FE): Click here
- DTC B279A is output (for 2TR-FE (w/o Dual VVT-i)): Click here
- DTC B279A is output (for 2TR-FE (w/ Dual VVT-i)): Click here
- DTC B279A is output (for 1KD-FTV): Click here
- DTC B279A is output (for 2KD-FTV): Click here
|
|
||||
| OK | ||
| ||
