2014-2019 Hiace · Service Manual ENGINE

P0489 Exhaust Gas Recirculation Control Circuit Low

Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The EGR system recirculates exhaust gases in a way that suits every driving condition. The recirculated gas mixes with intake air. Therefore, the EGR system can slow combustion speed and keep the combustion temperature down. This helps reduce NOx emission.
In order to increase EGR circulation efficiency, the ECM adjusts the lift amount of the EGR valve and the throttle valve angle.
P0489 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
5 seconds after engine is started
Open or short in VRV for EGR circuit for 5 seconds or more (1 trip detection logic).
  1. VRV for EGR
  2. Open or short in VRV for EGR circuit
  3. ECM
P0490 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
5 seconds after engine is started
Open or short in VRV for EGR circuit for 5 seconds or more (1 trip detection logic).
  1. VRV for EGR
  2. Open or short in VRV for EGR circuit
  3. ECM
Related Data List 
DTC No.
Data List
P0489
  1. Actual EGR Valve Pos.
  2. Target EGR Valve Pos.
P0490

WIRING DIAGRAM

Refer to DTC P0400 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT VRV FOR EGR
  1. Inspect the VRV for EGR (Click here).



NG
Go to step 5
OK


2. CHECK TERMINAL VOLTAGE (POWER SOURCE)

  1. A255071E17
    Disconnect the VRV for EGR connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D55-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to VRV for EGR)

  1. Reconnect the VRV for EGR connector.



NG
Go to step 6
OK


3. CHECK HARNESS AND CONNECTOR (VRV FOR EGR - ECM)
  1. Disconnect the VRV for EGR connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D55-2 - D105-83 (EGR)
    Always
    Below 1 Ω
    D55-2 or D105-83 (EGR) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the VRV for EGR connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


4. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7
5. REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
  1. Replace the electric EGR control valve assembly (Click here).



NEXT
Go to step 7
6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.

    HINT:
    If the voltage at the VRV for EGR connector is not 11 to 14 V, repair or replace the harness and connector between the VRV for EGR and the EFI MAIN relay.


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine.

  1. Idle the engine for 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0489 Exhaust Gas Recirculation Control Circuit Low (+ P0490) (Oct 2014 – Dec 2014)P0489 Exhaust Gas Recirculation Control Circuit Low (+ P0490) (Apr 2016 – Dec 2016) →